FAA / Advisory circular

AC 25.1309-1B

System Design and Analysis

System design, failure conditions, analysis and the evidence supporting a system safety assessment.

Start with the scope.

Guidance for showing compliance with §25.1309. Confirm the applicable amendment level and accepted means for the programme.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Find your starting point

What are you looking into?

Go directly to a useful part of the document.

Read the source

The document, within reach.

FAA source document

Printed page A-2

PDF page 53 of 75

FAA source text, reformatted for reading. Page boundaries and paragraph numbers are retained.

functional categories as non-essential, essential, and critical. However, for all practical purposes, the non-essential category was synonymous with the minor category in the BCAR; the essential category spanned the BCAR major and hazardous categories; and critical was the same as catastrophic in the BCAR. The qualitative and quantitative probabilities that were defined in AC 25.1309-1, and the described application of those probabilities, were, for the most part, the same as the BCAR.

A.4 FAA AC 25.1309-1A. In the 1980s, the FAA and the Joint Aviation Authorities (JAA) of Europe harmonized SSA requirements in § 25.1309 and Joint Airworthiness Requirement 25.1309, and the guidance in AC 25.1309-1A and its counterpart JAA Advisory Material Joint (AMJ) 25.1309. The only substantive difference between the AC and AMJ was that the JAA retained the “hazardous” category and its associated probability definitions from the BCAR; whereas the FAA did not but implied an intermediate “severe major” hazard category similar to “hazardous.” Otherwise, the definitions and probability values in the AC and AMJ were the same as those in the BCAR and Concorde standard. Both the AC and AMJ also contained a continuing strong emphasis on fail-safe design as the basic intent of the requirements.

A.5 This AC. In revising § 25.1309 at amendment 25-152 (89 FR 68706, August 27, 2024), the FAA added the “hazardous” category. In this AC, the FAA addresses five failure condition classifications (no safety effect, minor, major, hazardous, and catastrophic) and their associated qualitative and quantitative probabilities. These terms are harmonized with European Union Aviation Safety Agency (EASA) Acceptable Means of Compliance (AMC) 25.1309.

A.6 Quantitative Probability Terms. The quantitative probability values contained in this AC should not be applied independently of the qualitative guidance. For example, meeting the 1 x 10-9 per flight hour quantitative probability guidance alone is not sufficient to show compliance with the intent of the “extremely improbable” requirement of § 25.1309(b) if relevant experience indicates the failure condition can occur. The FAA’s guidance for using quantitative probability values to meet airworthiness standards has been unchanged since the 1970s. The probability numbers contained in this AC are provided solely for use in evaluating “statistically controllable” hazard contributors within the context of the analysis methodology described. The quantitative values in this AC do not represent FAA accident-rate goals or expectations. The values are unchanged from those derived for the Concorde program because it has been shown in service that the actual system safety achieved using fail-safe design techniques and the combination of qualitative and quantitative guidance in this AC continues to be acceptable.

AC 25.1309-1B · A-2Open saved PDF here ↗

Saved from the FAA on November 16, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Connect the analysis
to the design.

A useful assessment explains why the architecture meets the safety objectives, what assumptions it relies on, and how those assumptions will be verified. We use the guidance to structure the questions and evidence around the actual system.

01 / Define the failure conditions

Begin with functions and effects.

Describe the operating context, affected functions, crew response and interactions with other systems. Carry the resulting safety objectives into the architecture and requirements.

FHA guidance · §6.2 →
02 / Examine the architecture

Make independence and exposure explicit.

Explain monitoring, fault containment and common causes. Examine significant latent failures and the assumptions about how long a failure can remain present.

Latent failures · §5.3.6 →Common cause · §7.4 →
Methods and editions need to be agreed.

Our practice uses ARP4761A and ARP4754B to organise safety assessment and systems development work. This AC refers to ARP 4761 and ARP 4754 without revision letters. Its references alone do not establish acceptance of a particular revision for a programme.

Source edition and reading coverage

75 original pages. 55 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 90e625593d472b74ec69fbcefe97649f97794410dbe844f7684b397121ac5a92

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →