FAA / Advisory circular

AC 25.1309-1B

System Design and Analysis

System design, failure conditions, analysis and the evidence supporting a system safety assessment.

Start with the scope.

Guidance for showing compliance with §25.1309. Confirm the applicable amendment level and accepted means for the programme.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Find your starting point

What are you looking into?

Go directly to a useful part of the document.

Read the source

The document, within reach.

FAA source document

Printed page 5-1

PDF page 27 of 75

FAA source text, reformatted for reading. Page boundaries and paragraph numbers are retained.

CHAPTER 5. COMPLIANCE WITH § 25.1309

5.1 Overview. This chapter describes specific means of compliance with § 25.1309. The applicant would benefit from obtaining early agreement from the FAA on its chosen means of compliance.

5.2 Compliance with § 25.1309(a).

5.2.1 Equipment, systems, and installations regulated by § 25.1309(a)(1) must be shown to function properly when installed. The “airplane operating and environmental conditions” that must be considered under that regulation include the full normal operating envelope of the airplane found in the airplane flight manual (AFM) together with any modification to that envelope associated with abnormal or emergency procedures. External environmental conditions that the airplane is reasonably expected to encounter should be considered, such as atmospheric turbulence, high-intensity radiated fields, lightning, and precipitation. The severity of the external environmental conditions that should be considered is limited to those established by certification standards and precedence.

5.2.2 In addition to the external operating and environmental conditions, the effect of the operating and environmental conditions within the airplane should be considered. Examples of these effects include the following: vibration and acceleration loads, variations in fluid pressure and electrical power, fluid or vapor contamination due to either the normal environment or accidental leaks or spillage and handling by personnel, heat radiated from nearby equipment, and electromagnetic emission from installed equipment. AC 21-16 recognizes RTCA Document DO-160, which defines a series of standard environmental test conditions and procedures that may be used to support compliance. Environmental test procedures contained in technical standard orders (TSOs), or other environmental test standards approved for equipment qualifications, can be used to support compliance. The conditions under which the installed equipment will be operated should be equal to or less severe than the environment for which the equipment is qualified.

5.2.3 The applicant may substantiate the proper functioning of equipment, systems, and installations under the operating and environmental conditions approved for the airplane by test and/or analysis, or reference to comparable service experience on other airplanes if shown to be valid for the proposed installation. For the equipment, systems, and installations covered by § 25.1309(a)(1), the compliance demonstration should also confirm that their normal functioning does not adversely affect the proper functioning of other equipment, systems, or installations covered by § 25.1309(a)(1).

5.2.4 The equipment, systems, and installations addressed by § 25.1309(a)(2) are not required to meet § 25.1309(a)(1). These equipment, systems, and installations are those associated with miscellaneous systems intended for convenience, such as passenger

AC 25.1309-1B · 5-1Open saved PDF here ↗

Saved from the FAA on November 16, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Connect the analysis
to the design.

A useful assessment explains why the architecture meets the safety objectives, what assumptions it relies on, and how those assumptions will be verified. We use the guidance to structure the questions and evidence around the actual system.

01 / Define the failure conditions

Begin with functions and effects.

Describe the operating context, affected functions, crew response and interactions with other systems. Carry the resulting safety objectives into the architecture and requirements.

FHA guidance · §6.2 →
02 / Examine the architecture

Make independence and exposure explicit.

Explain monitoring, fault containment and common causes. Examine significant latent failures and the assumptions about how long a failure can remain present.

Latent failures · §5.3.6 →Common cause · §7.4 →
Methods and editions need to be agreed.

Our practice uses ARP4761A and ARP4754B to organise safety assessment and systems development work. This AC refers to ARP 4761 and ARP 4754 without revision letters. Its references alone do not establish acceptance of a particular revision for a programme.

Source edition and reading coverage

75 original pages. 55 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 90e625593d472b74ec69fbcefe97649f97794410dbe844f7684b397121ac5a92

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →