Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 5 6/13/2014
Failure Condition Suggested Verification Possible Additional
Categories Method Methods
Minor Analysis Flight Testing *3
Major Analysis Simulation
Ground Test Flight Test
Hazardous/ Analysis Simulation
Severe-Major Ground Test
Limited Flight Tests *1, *2
Catastrophic Analysis Limited Flight Tests *1, *2
Simulation
Ground Test
* - Notes:
1 - This should be determined on a case-to-case basis.
2 - Minimize flight testing as a verification methodology, for this combination of
provided integrity and failure condition category, due to safety in testing
considerations. However, desirable flight testing may be feasible for some
aspects if observing proper identification of flight test risk and assessments,
and risk mitigations, in accordance with FAA Order 4040.26.
3 - For analysis or verification, those probable failures evaluated as having minor
effects, flight testing is an option if the effects are not obvious or if there can
only be evaluation of closed loop effects in flight.
Figure AC 27 MG 17-1
Verification Methodology
(ii) Due to AdFC inherent complexity, AdFC systems that typically have a large
number of test cases of single and multiple failures should be investigated to verify the
safety functions under all failure conditions.
(A) Non-Real Time Computer Analysis. At the beginning of the development
process, when system components are not yet available in hardware, non-real time
computer simulation is a useful tool for supporting the preliminary system safety
assessment. This allows, at an early stage of the development, a prediction of the
effects and an assessment of the criticality of failure modes of the flight control system.
(B) Pilot-in-the-Loop Simulator Test. It may be practical to use a flight
simulator (FS) to qualitatively verify safety assessments for certain AdFC failure
conditions that would be high risk or unsafe to perform in flight. These assessments
may be part of the SA process used to show compliance with specific regulations. For
Page MG 17 - 4
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.