FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-1

PDF page 270 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 270
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

                     CHAPTER 2. PART 27
                  AIRWORTHINESS STANDARDS
               NORMAL CATEGORY ROTORCRAFT

             SUBPART D - DESIGN AND CONSTRUCTION

               DESIGN AND CONSTRUCTION - GENERAL


AC 27.601.  § 27.601 DESIGN.

     a. Explanation.

         (1) This rule requires that no design features or details be used that experience
has shown to be hazardous or unreliable.

         (2) Further, the rule requires that the suitability of each questionable design
detail and part must be established by tests.

     b. Procedures.

         (1) This rule is met partially by a review of service history of earlier model
rotorcraft, or for a new model, review of service experience of models with similar
design features. Specifically, this rule covers “features or details” such as the following:

                  (i)   Seat track-to-seat interface fittings. These fittings should have
adequate locking devices to prevent both premature structural failure and premature
unlatching.

                   (ii)   Seat belt and harness should be of a type and construction that
service experience has shown to be easy to don and unlatch and remove. They should
also be of a type that is reliable, does not interfere with egress, and does not sustain
unnecessary wear and tear under normal operations.

                    (iii)   Metallic parts less than a certain thickness gauge and composite
materials less than a certain number of plies should not be used. The minimum
thickness and number of plies should be based to a large degree on service (normal
wear and tear) experience with similar designs.

         (2) The effects of service wear on the loading of critical components should be
considered. Flight testing, ground testing, and analyses may be used in these
considerations.

         (3) Tests are required for details and parts which the applicant chooses to use
after questions have arisen concerning their suitability.



                                                        Page D - 1

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →