FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page Apdx B-1

PDF page 1175 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 1175
AC 27-1B · Apdx B-1Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/4/2016                                                  AC 27-1B, Chg 7


AC 27 APPENDIX B.    AIRWORTHINESS GUIDANCE FOR ROTORCRAFT INSTRUMENT
                      FLIGHT.

    a. Explanation.

         (1) Requirements for instrument flight rules (IFR) have been incorporated into Appendix B to
part 27, Amendment 19. Various information from previous interim standards, procedures, test
techniques, and acceptable means of compliance for rotorcraft IFR flight is included in the following
sections.

         (2) Amendment 27-44 made a change to paragraph V. Static Lateral Directional Stability,
concurrent with the change to § 27.177, to allow for a small range of sideslip angles (2-3 degrees) for
which sideslip angles need not increase steadily with control deflection. The previous rule language
stating that directional control position must increase in approximate constant proportion with sideslip
angle has been replaced. The intent of this change is that an increase in directional control position must
produce an increase in sideslip angle linearly. At greater sideslip angles appropriate to the type
rotorcraft, increase in directional control position need not produce a linear increase in sideslip angle but
should not become neutral or negative. The change in paragraph VII revised the current requirement to
clearly state the requirements to be met in the event of a stability augmentation system (SAS) failure.1

    b. Procedures.

         (1) General.

                  (i) The certificated instrument flight envelope may be more restrictive than the visual flight
rules (VFR) envelope in terms of weight, CG, speed, altitude, or rate of climb and descent. The approved
envelope should be operationally practical and not impose constraints with which the crew has difficulty
complying. The IFR altitude envelope should extend to at least 10,000 feet to be operationally practical in
the National Airways System.

                    (ii) Controllability requirements are to be met from 0.9 VMINI to 1.1 VNEI. Stability requirements
must be met where specified. Stability devices are to be designed to allow safe flight following failures.
The evaluating pilot should assure that all equipment and devices installed for IFR, including reasonable
failures of that equipment, do not compromise the VFR approval for that rotorcraft. For example, stability
system failures can cause loss of swashplate or tail rotor control travel when failed in a hardover
condition.  If the device remains in the hardover position after the stability system is turned off, control
capability can be compromised. Cyclic controllability tests at high speed and at the limiting rearward flight
condition, or tail rotor tests in sideward flight at high altitude, may reveal a lower control capability and a
more restrictive envelope. Revision to the envelope approved for VFR conditions may be required when
stability equipment is installed. In addition, controllability testing should be accomplished with the control
rigging set at the most adverse production tolerance for the test condition (e.g., minimum forward
swashplate for high speed testing).

         (2) Trim. Compliance with the IFR trim requirement may be met by use of a magnetic brake with
a recentering button, an electrically driven trim system activated by a “beeper” type control, or other
means, so long as the system does not introduce any objectionable discontinuities in the force gradient or
otherwise result in objectionable flight characteristics. Trim release devices should be free of
objectionable stick jump. Electrically driven trim systems should have a smooth change in force with a
rate compatible with the normal rotorcraft maneuvers. Only the cyclic trim control must exhibit positive
self-centering characteristics. Collective and directional controls are not required to incorporate positive
self-centering characteristics. Movement of the trim controls should produce a similar effect on the
rotorcraft in a plane parallel to that of the control motion. The control system free play and breakout force
must be evaluated to assure a close and direct correlation between control input (force and deflection)

1 Paragraph VII was effective 9/17/2009 as part of the new and changed guidance material for the Performance and
Handling Qualities final rule (Amdt. 27-44, 73 FR 11000, Feb. 29, 2008).


                                                                    Page Apdx B - 1

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →