FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-1

PDF page 151 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 151
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

                     CHAPTER 2. PART 27
                  AIRWORTHINESS STANDARDS
               NORMAL CATEGORY ROTORCRAFT

             SUBPART C - STRENGTH REQUIREMENTS

              STRENGTH REQUIREMENTS - GENERAL


AC 27.301.  § 27.301 LOADS.

     a. Explanation.

         (1) The rule is a general statement concerning limit and ultimate loads and the
application of these loads to the rotorcraft.

         (2) Ultimate loads are limit loads multiplied by the prescribed factors of safety.

         (3) The specified loads are specified to be distributed appropriately or
conservatively and significant changes in distribution of the loads, as a result of
deflection, are specified to be taken into account.

     b. Procedures. The design criteria report and/or design loads report should
contain data that comply with the rule.

AC 27.303.  § 27.303 FACTOR OF SAFETY.

     a. Explanation.

         (1) Unless otherwise provided by Part 27, a factor of safety of 1.5 is required
and is applied as stated in the rule. This safety margin will ensure that the design
strength of the rotorcraft is greater than the design loads contained in Part 27.

         (2) Other rules, §§ 27.561(b)(3) and 27.787(c), specify use of defined ultimate
inertial forces for protection of occupants.

     b. Procedures.

         (1) The design criteria report and/or design loads report should contain data
that include the appropriate factor of safety.

         (2) The factor of safety multiplies the limit external and inertial loads. The rule
does allow the application of this factor to the resulting “limit internal” stresses if it is
more conservative.



                                                           Page C - 1

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →