FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 780

PDF page 780 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 780
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/4/2016                                      AC 27-1B, Chg 7


                        CHAPTER 3
                  AIRWORTHINESS STANDARDS
               NORMAL CATEGORY ROTORCRAFT

                 MISCELLANEOUS GUIDANCE (MG)

AC 27 MG 1.   CERTIFICATION PROCEDURE FOR ROTORCRAFT AVIONICS
            EQUIPMENT.

    a. Pretest Requirements.

       (1) General. This test guideline has been prepared as an aid in the evaluation of
rotorcraft avionics (aviation electronics) equipment installations. The criteria presented
are not exclusive, but are offered as one method of evaluating design practice and
performance. Consider the testing and qualification of an electronic installation as
consisting of three phases: preinstallation, ground, and flight. The amount of testing
necessary during each phase will vary with the amount of testing performed on previous
phases. For example, if a system is produced under a TSOA, pre-installation
performance relative to TSO functions is likely substantiated. Therefore, the ground
and flight test to assess these functions may be able to be reduced. However, a TSOA
does not mean that the specific system meets installed performance requirements per
14 CFR part 27. In addition, a thorough ground testing program should result in
reduction in necessary flight testing. When the operating or airworthiness regulations
require a system to perform its intended function, we strongly recommend the use of
TSO’d equipment or the submission of data substantiating the equipment performance.

       (2) Regulatory References. Sections 27.1301 and 27.1309 (through
Amendment 27-19).

       (3) System Design. Sufficient data should accompany systems or equipment
presented for installation approval, when not qualified by TSO or other approval means,
to substantiate the design acceptability.

               (i) Operation of Controls. The operation of controls intended for use during
flight, in all possible position combinations and sequences, should not result in a
condition that would be detrimental to the continued safe performance of the system.

                (ii) Electrical Shock. Design systems to minimize the risk of dangerous
electrical shock under all probable conditions.

                 (iii) Fire Hazard. The design of the system should be such that all
components meet the applicable fire and smoke protection requirements of §§ 27.853
and 27.863. Cables and equipment for installation in designated fire zones used during
emergency procedures should be fire resistant.



                                                        Page MG 1 -1

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →