FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-13

PDF page 573 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 573
AC 27-1B · F-13Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

3/31/2014                                      AC 27-1B, Chg 4


AC 27.1309.   § 27.1309 (Amendment 27-21) EQUIPMENT, SYSTEMS, AND
             INSTALLATIONS.

     a. Types of Equipment. Section 27.1309 of the Title 14 CFR regulations covers,
but is not limited to, electrical, pneumatic, and hydraulic power sources, distribution, and
corresponding utilization systems.

     b. Environmental Qualification.

         (1) Laboratory Tests.

                  (i) Environmental Standards. In order to ensure that the components and
systems under consideration will function properly when exposed to adverse
environments, they should be tested in the laboratory under a simulated adverse
environment.  If a TSO exists and it is appropriate in environmental range and
performance for an equipment installation, it is preferable that the equipment be TSO
approved.  If there is no applicable TSO or an existing TSO does not provide for a
sufficiently adverse environment, the latest revision of Radio Technical Commission for
Aeronautics (RTCA) Document DO-160 is an acceptable environmental standard for
laboratory qualification of aircraft equipment.

                   (ii) Adverse environmental variables for all types of required and critical
equipment include, but are not necessarily limited to, temperature, humidity, vibration,
shock, altitude, overpressure, and power source transients.

                    (iii) For electrical and electronic equipment, adverse environmental
variables include all of (b)(1)(i) and (ii) above plus overvoltage and undervoltage.
Electronic equipment should also be tested for electromagnetic interference (EMI).
These tests should include both emission and susceptibility evaluations of both
conducted and radiated EMI.

               (iv) Explosion Tests. Those items of electrical and electronic equipment
that are to be located in areas subject to flammable fluids and vapors, as a result of any
single probable malfunction or failure including failure of couplings or lines, should be
tested as an ignition source. These tests consist of normal operation of the equipment
in a physically contained explosive atmosphere. The explosion test procedure in the
latest revision of DO-160 will satisfy this requirement.  If another standard is used that is
at least as good as the latest revision of DO-160, it may also be accepted to satisfy this
requirement.

         (2) Installed Environmental Tests. After the environmental ratings of the
components and systems have been established, it should be ensured that as installed,
these ratings will not be exceeded. Normally, installed equipment need not be
instrumented and tested in flight, and it is not necessary to instrument the compartment
or rack where the equipment is installed. Satisfactory environment and equipment
compatibility are ensured by selection of the proper environmental category of


                                                          Page F - 13

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →