FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-51

PDF page 638 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 638
AC 27-1B · F-51Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

3/31/2014                                      AC 27-1B, Chg 4


         (v) A malfunction of the autopilot during a coupled ILS approach should not
place the aircraft in an attitude which would preclude conducting a satisfactory go-
around or landing.

   e. Servo Authority. The automatic pilot system should be installed and adjusted so
the system tolerances established during certification tests can be maintained in normal
operation. This may be assured by conducting flight tests at the extremes of the
tolerances. Those tests conducted to determine that the automatic pilot system will
adequately control the aircraft should establish the lower limit. Those tests to determine
that the automatic pilot will not impose dangerous loads or deviation from the flight path
should be conducted at the upper limit. Appropriate aircraft loadings to produce the
critical results should be used.

    f. Rotorcraft Flight Manual Information. The following information should be placed
in the rotorcraft flight manual:

      (1) In the Operating Limitations Section: Airspeed, Maximum Height Loss
following AFCS malfunction for each phase of flight, Minimum Use Height where
appropriate, and other applicable operating limitations for use of the autopilot.

      (2) In the Operating Procedures Section: Normal operation information.

      (3) In the Emergency Operation Procedures Section:

            (i) A statement of the downward flight path deviation in the cruise, climb, and
descent configurations and the maneuvering flight configuration in accordance with
paragraph d(5) above, if this deviation exceeds 100 feet.

             (ii) True profiles of deviations below the glide slope or projected flare path for
the critical conditions tested (see paragraph d. above and Figure AC 27.1329-2) and the
deviation profile indicating the lowest altitude at which the autopilot can be used (see
paragraph d. above), if applicable, and if this deviation exceeds 100 feet or results in
excessive deviation for an ILS approach.

AC 27.1329A.  § 27.1329 (Amendment 27-35) AUTOMATIC PILOT SYSTEM.

   a. Explanation. Amendment 27-35 adds paragraph (f) to § 27.1329, which requires a
means of indicating to the pilots the current mode of operation for those automatic pilot
systems that can be coupled to the airborne navigation equipment.

   b. Procedures. The policy material pertaining to section 27.1329 of this AC remains
in effect with the following additions:

      (1) Mode annunciation must indicate the state of the system, including mode
change and disengagement. Mode annunciation should be presented in a manner
compatible with flightcrew procedures and tasks and be consistent with other flight deck


                                                          Page F - 51

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →