FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page B-1

PDF page 49 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 49
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

                     CHAPTER 2. PART 27
                  AIRWORTHINESS STANDARDS
               NORMAL CATEGORY ROTORCRAFT

                     SUBPART B - FLIGHT

                         GENERAL

AC 27.21. § 27.21 (Amendment 27-21) PROOF OF COMPLIANCE.

     a. Explanation.

         (1) This section provides a degree of latitude for the FAA/AUTHORITY test
team in selecting the combination of tests or inspections required to demonstrate
compliance with the regulations. Compliance should be shown for applicable
combinations of gross weight, center of gravity, altitude, temperature, airspeed, rotor
RPM, etc. Engineering tests are designed to investigate the overall capabilities and
characteristics of the rotorcraft throughout its operational envelope. Testing will identify
operating limitations, normal and emergency procedures, and performance information
to be included in the FAA/AUTHORITY-approved portion of the flight manual. The
testing must also provide a means of verifying that the rotorcraft’s actual performance,
structural design parameters, propulsion components, and systems operations are
consistent with all certification requirements.

         (2) Section 21.35 requires, in part, that the applicant show compliance with the
applicable certification requirements, including flight test, prior to official FAA Type
Inspection Authorization (TIA) testing. Compliance in most cases requires systematic
flight testing by the applicant. After the applicant has submitted sufficient data to the
FAA/AUTHORITY showing that compliance has been met, the FAA/AUTHORITY will
conduct any inspections, flight, or ground tests required to verify the applicant’s test
results. FAA/AUTHORITY compliance may be partially determined from tests
conducted by the applicant if the configuration (conformity) of the rotorcraft can be
verified. Compliance may be based on the applicant’s engineering data and a spot
check or validation through FAA/AUTHORITY flight tests. The FAA/AUTHORITY
testing should obtain validation at critical combinations of proposed flight variables if
compliance cannot be inferred using engineering judgment from the combinations
investigated.

         (3) Performance tests include minimum operating speed (hover), takeoff and
landing, climb, glide, height-velocity, and power available. Certain other performance
tests, such as critical engine survey for multiengine installations, may be conducted to
meet specific requirements. Detailed performance test procedures and allowable
extrapolation or simulation limits are contained in the respective paragraphs in this AC.

                  (i)   Hover tests are conducted to determine various combinations of
altitude, temperature, and gross weight for both in-ground-effect (IGE) and, if required


                                                        Page B - 1

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →