Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
by the applicant, out-of-ground effect (OGE) conditions. From these data, the hover
ceiling may be calculated.
(ii) Takeoff and landing tests are conducted to determine that a takeoff or
landing can be safely executed without requiring exceptional piloting skill or favorable
conditions at any approved combination of altitude, temperature, and gross weight.
(iii) For rotorcraft other than helicopters, climb tests establish the
variations of rate-of-climb at the best rate-of-climb or published climb airspeed(s) at
various combinations of altitude, temperature, and gross weight. For helicopter, climb
tests are conducted as required to determine the best rate-of-climb speed, Vy.
(iv) Height-velocity tests are conducted to determine the boundaries of the
height versus airspeed envelope from which a safe landing can be accomplished
following an engine failure.
(v) Power available tests are conducted to verify the calculated installed
specification engine performance model on which published performance is based.
(4) The purpose of rotorcraft stability and control tests is to verify that the
rotorcraft possesses the minimum qualitative and quantitative flying qualities and
handling characteristics required by the applicable regulations. In order to assess the
handling qualities, standardized test procedures must be utilized and the results
analyzed by accepted methods. Section 27.21(a) allows calculation and inference
which includes extrapolation and simulation, whereas § 27.21(b) requires demonstration
of controllability, stability, and trim. Combinations of § 27.21(a) and (b) may be used to
show compliance with the operating envelope limits. Test methods and equipment are
described in individual paragraphs of this advisory circular.
b. Procedures.
(1) Efforts should begin early in the certification program to provide advice and
assistance to the applicant to ensure coverage of all certification requirements. The
applicant should develop a comprehensive test plan which includes the required
instrumentation.
(2) The tests and findings specified in paragraph AC 27.21a(3) are required of
the applicant to show basic airworthiness and probable compliance with the minimum
requirements specified in the applicable regulations. After these basic findings have
been submitted and reviewed, a Type Inspection Authorization, or equivalent, can be
issued. The FAA/AUTHORITY will develop a systematic plan to spotcheck and confirm
that compliance with the regulations has been shown. The test plan will consider
combinations of weight, center of gravity, and RPM and cover the range of altitude and
temperature for which certification is requested.
Page B - 2
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.