Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
(5) Other static system considerations are included in paragraphs AC 27.1323
and AC 27 Appendix B.
AC 27.1327. § 27.1327 (Amendment 27-13) MAGNETIC DIRECTION INDICATOR.
a. Background. This section contains specific requirements regarding installation
and functioning of a magnetic direction indicator. The magnetic direction indicator
(commonly referred to as a compass) described by this paragraph is the unit required
by § 27.1303(c) or the unit or system required for IFR operation by Appendix B VIII(a) to
Part 27. Both of these indicators provide the pilot with an aircraft heading which is
referenced to the earth’s magnetic field. The unit required by § 27.1303(c) is the
indicator commonly referred to as a “whiskey compass.” The unit was given this
designation because early units were constructed using alcohol as the medium in which
the compass ball floats. This unit is generally approved as meeting the requirements of
TSO-C7c. The indicator required by Appendix B to Part 27 is usually a system of units
which meets the requirements of TSO-C6c.
b. Procedures. In showing compliance to § 27.1327(a), generally the magnetic
indicator and its respective components will be tested to an appropriate standard such
as RTCA DO 160B for use in a rotorcraft. If the unit functioned properly as described in
the TSO during this testing, then no additional evaluation is generally required
concerning vibration immunity. To determine the immunity of the indicator (system)
from magnetic effects and its installed accuracy, a ground and flight test should be
performed. This test should turn the rotorcraft a full 360° heading change in 45°
increments. The indicator should not have an error in excess of 10° on any of the 45°
increments. When performing these tests, the electrical equipment and systems should
be functioning normally, and the effect of windshield heating (if installed) should be
investigated. During this investigation, it is permissible for the error caused by the effect
of the operation of electrical equipment on the indicator required by § 27.1303(c) to
exceed 10° if a gyroscopic heading indicator is installed. This gyroscopic heading
indicator may either be a directional gyro or a slaved compass system (gyro-stabilized
magnetic direction indicator). The results of the investigation may be used to construct
the calibration placard which is required by § 27.1547. It should be noted that a
calibration placard has not been traditionally required for slaved compass systems.
Also, it should be emphasized that other aspects of the functioning and installation of
these indicators should comply with the other general requirements (i.e., §§ 27.1301,
27.1309, 27.1555, etc.).
AC 27.1329. § 27.1329 (Amendment 27-21) AUTOMATIC PILOT SYSTEM.
a. Explanation. The automatic flight control systems used on most modern rotorcraft
often perform two different and distinct functions when viewed from a regulatory
compliance aspect. These two functions are an augmentation of the stability of the
rotorcraft and a pilot aid in maintaining attitude, altitude, and airspeed, or in radio
navigation tasks. The first function of stability is not covered by § 27.1329 but is
included under § 27.672. The second function as a pilot aid is the automatic pilot
Page F - 41
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.