FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-30

PDF page 590 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 590
AC 27-1B · F-30Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                     3/31/2014


discussed previously for level reduction. Level D qualification is less than Level C and
is typically employed for required systems or equipment that do not exhibit the fault
potential of the higher categories. Level E qualification is less than Level D and is
employed in those systems or equipment that are not required by the regulations and
whose malfunction results in no safety effect on the rotorcraft or its crew and occupants.
Examples are entertainment systems, powered seats, etc.

             (3) Although a rough correlation exists between software levels and
criticality levels that in turn relate to a probability in numbers, these numbers cannot be
applied to software to determine reliability obtained by the processes delineated in
DO-178C and at this time, have no correlation with probability.

      g. Airborne Electronic Hardware (AEH). For airborne complex custom micro­
coded electronic components assessed as level A, B, or C in the safety assessment,
RTCA Document DO-254, “Design Assurance Guidance for Airborne Electronic
Hardware,” dated April 19, 2000, provides certification guidance for qualification and
subsequent approval of these components. Per DO-254, the component will need to be
identified as either “simple” or “complex” and tagged to one of the five failure condition
classifications. Based on these identifiers, DO-254 provides the guidance to show
compliance to § 27.1309. Although RTCA/DO-254 applies specifically to complex
custom micro-coded components, applicants are highly encouraged to apply DO-254 to
other hardware components up through to the line replaceable unit and systems level.

AC 27.1309A.   § 27.1309 (Amendment 27-46) EQUIPMENT, SYSTEMS, AND
INSTALLATIONS.

     a. Explanation. Amendment 27-46 removed § 27.1309(d) and incorporated a
dedicated rule § 27.1316 to better address Electrical and Electronic System Lightning
Protection.

     b. Procedures.  If the certification basis includes § 27.1309 (d), applicants should
utilize the previous section of this guidance (section 27.1309 of this AC) to show
compliance with protection from lightning effects.  If the certification basis includes
§ 27.1316, applicants should show compliance with protection from lightning effects by
referring to the applicable section of this AC (section 27.1316, Electrical and Electronic
System Lightning Protection). The paragraphs other than b.(3) of section 27.1309 of
this AC are still applicable. This should be coordinated with the appropriate certification
office early in the discussions so the path to show compliance with electrical and
electronic system lightning protection is clear to the applicant and authority.





Page F - 30

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →