Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
CHAPTER 2. PART 27
AIRWORTHINESS STANDARDS
NORMAL CATEGORY ROTORCRAFT
SUBPART G - OPERATING LIMITATIONS AND INFORMATION
AC 27.1501. § 27.1501 (Amendment 27-14) GENERAL.
Explanation. This section simply requires specified operating limitations in addition
to any other information necessary for the safe operation of the rotorcraft to be
determined. Secondly, it requires that this pertinent information be made readily
available to the crew members as required in the various sections of this subpart.
OPERATING LIMITATIONS
AC 27.1503. § 27.1503 AIRSPEED LIMITATIONS: GENERAL.
a. Explanation. This section requires that a safe operating speed range be
established for all rotorcraft. If the safe operating speed range varies with operating
conditions (rotor speed, power, etc.), ambient conditions (altitude and/or temperature),
rotorcraft configuration (gross weight, center of gravity, and/or external equipment), or
type of operation (in ground effect (IGE), instrument flight rules (IFR), etc.), airspeed
limitations that correspond with the most critical combinations of these factors must be
established.
b. Procedures.
(1) Airspeed Limitations. The airspeed limitations for each critical combination
of factors are established by tests or analyses and verified by flight test. The following
are airspeed limitations that are typically required depending on the particular rotorcraft
design:
(i) VNE (Power-On). See paragraph AC 27.1505.
(ii) VNE (One-Engine-Inoperative (OEI)). See paragraph AC 27.1505.
(iii) VNE (Power-Off). See paragraph AC 27.1505.
(iv) VLO (Maximum Airspeed for Landing Gear Operation). Compliance
with structural, handling qualities, and controllability requirements should be
demonstrated at the airspeed limit.
(v) VLE (Maximum Airspeed Landing Gear Extended). If this airspeed
limit differs from the maximum gear operation speed, compliance with the applicable
structural, handling qualities, and controllability requirements should be demonstrated.
Page G - 1
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.