Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
CHAPTER 2. PART 27
AIRWORTHINESS STANDARDS
NORMAL CATEGORY ROTORCRAFT
SUBPART A - GENERAL
AC 27.1. § 27.1 APPLICABILITY.
a. Explanation. This section prescribes the rotorcraft categories eligible for
certification under this Part. There is no minimum weight limit for certification under
Part 29; however, Part 27 is applicable to rotorcraft with maximum weights of
6,000 pounds or less.
(1) Without Engine Isolation. For single-engine rotorcraft and multiengine
rotorcraft without engine isolation, the height-velocity (HV) diagram is conducted with
sudden failure of all engines, and the takeoff maneuver must pass through the clear
area of the diagram to the 50-foot point with all engines operating.
(2) With Engine Isolation. Part 27 multiengine rotorcraft may be certificated
with engine isolation features (reference paragraph AC 27 MG 3). These rotorcraft are
not required to meet the Part 29, Category A, performance requirements, and continued
flight after an engine failure is not assured since under some conditions failure of the
remaining engine may occur after a limited time. The takeoff is conducted with all
engines operating, while the height-velocity diagram is determined with the most critical
engine inoperative. If complete Part 29, Category A, design features and performance
are achieved, the Category A performance may be included in the
FAA/AUTHORITY-approved portion of the Rotorcraft Flight Manual although this
performance is not required by the regulations.
b. Procedures. None.
AC 27.1A. § 27.1 (Amendment 27-33) APPLICABILITY.
a. Explanation. Amendment 33 formally introduced the requirements for
certification of a Part 27 rotorcraft to Category A design and performance standards.
These standards are found in Appendix C of Part 27. The establishment of Category A
design and performance for multiengine Part 27 rotorcraft is still voluntary. If so
requested, the corresponding AC 29-2C material applies.
b. Procedures. None
Page A - 1
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.