Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
AC 21.39. § 21.39 (Amendment 21-59) FLIGHT TEST INSTRUMENT CALIBRATION
AND CORRECTION REPORT.
a. Explanation. It is the applicant’s responsibility to provide instrumentation for all
parameters needed to show compliance with the airworthiness regulations.
(1) For those data which are necessary to show compliance with the
regulations, a permanent record should be established. A permanent record is
acceptable in either graphical or photographic form, and in some instances a manual
recording may be satisfactory.
(2) Regardless of the record form, the accuracy of the record must be
established by reference to a laboratory standard traceable to the National Bureau of
Standards.
(3) If multiplexing is used, the time base must be synchronized to a reference
point from which the magnitude of each parameter can unquestionably be determined.
Also, the sampling rate should be sufficiently frequent to ensure that the maximums,
minimums, and trends of magnitude of the parameter are recorded with respect to time.
b. Procedures. Prior to conducting flight tests, the FAA/AUTHORITY flight test
team should review the applicant’s flight test instrumentation, calibration, and correction
report.
(1) The frequency of recalibration varies with the consistency of the
instrumentation under consideration. For example, cyclic and collective position is
sometimes calibrated immediately before and after a flight where these parameters are
used to provide critical flight data. Six months is a typical interval for recording/signal
conditioning and nonstrain gage sensors, while 1 year is typical for strain gaged
components. Also, environmental effects such as vibration, humidity, temperature, etc.,
should be considered when determining whether recalibration is necessary.
(2) The highest and lowest magnitude of the parameter being recorded should
be considered when establishing the scale for instrumentation. Ideally, the highest
magnitude throughout the flight would fall on the maximum indicating point of the
recording.
Page FAR 21 - 6
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.