Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
AC 27.1B § 27.1 (Amendment 27-37) APPLICABILITY.
a. Explanation. Amendment 27-37 increases the normal category rotorcraft
maximum gross weight limit from 6,000 to 7,000 pounds and introduces new
airworthiness requirements. The gross weight increase was intended to compensate for
past regulatory actions that, in effect, cumulatively increased the gross weight of normal
category rotorcraft. The amendment also adds an explicit nine-passenger seat
limitation. The new airworthiness requirements were intended to increase the level of
safety to support a potential increase in the number of passenger seats associated with
the increase in maximum gross weight limit.
b. Procedures. None
AC 27.2 § 27.2 (Amendment 27-28) SPECIAL RETROACTIVE REQUIREMENTS.
a. Explanation.
(1) Amendment 27-28 requires a combined shoulder harness and safety belt
(also called a torso restraint system) at each occupant’s seat for all rotorcraft
manufactured after September 16, 1992.
(2) The design features of the restraint system are mainly contained in this
section rather than having to refer to other sections within Part 27 except for a general
reference to the differing strength standards between earlier static strength only
standards and the static and dynamic strength standards of Amendment 27-25.
(3) Combined safety belt and harness strength standards system follows:
(i) Those rotorcraft type designs certificated to static strength standards
alone prior to Amendment 27-25, such as 4 g’s forward may use belt and harness
systems, characterized as 1,500 pounds strength systems, provided they comply with
those standards. TSO C22f and earlier restraint systems have such ratings. A
combined belt and harness with a 1,500 pounds rating, which comply with the Part 27
standards for the rotorcraft type design, but are not necessarily TSO approved, may be
approved as a part of the type design. Such design information for a non-TSO’d item
would be included in a note on the aircraft type certificate data sheet (TCDS) or
specification sheet by part number as “required equipment.” TSO C114-approved torso
restraint systems, characterized as 3,000 pounds strength system, may be used
provided the design features comply with this section, but no special information on the
TCDS is necessary.
(ii) Those rotorcraft type designs certified to dynamic test requirements of
Amendment 27-25 should use torso restraint systems approved under TSO C114 or
approved under equivalent standards such as those contained in Part 27.
(4) Load Distribution and Design Requirements. Although not stated in § 27.2,
a 60 percent and 40 percent load distribution between the safety belt and harness,
Page A - 2
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.