FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page A-3

PDF page 47 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 47
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

respectively, is required in § 27.785(g). The safety belt should withstand 100 percent if
the safety belt is capable of being used alone. Also, the safety belt or harness
attachments to the seat or structure should include the 1.33 factor described in
§ 27.785(f)(2) of Amendment 27-21 for those rotorcraft with that certification criteria or
should include the 1.15 factor as described in § 27.625 (and predecessor Part 6)
standards for those rotorcraft with the earlier certification criteria. A factor is used
whether test or analysis methods are used for static substantiation of the seating
systems. Refer to paragraph AC 27.785c(i) (§ 27.785).

         (5) The companion operating rule change of Amendment 91-220, amended
§ 91.205 (Amendment 91-223), affecting the aircraft equipment requirements.
Operating rule § 91.107(a) already requires use of the harness whenever the aircraft
seat is so equipped.

     b. Procedures.

         (1) A TSO-approved combined safety belt and harness or torso restraint
system may be used provided the installation requirements in § 27.2 are satisfied. A
combined belt and harness (not necessarily TSO approved) may be approved as a part
of the rotorcraft type design and so noted on the aircraft specification or TCDS.

         (2) Structural analysis or static test may be used. For those rotorcraft designs
that are subject to the dynamic test standards of § 27.562, the torso restraint system is
required to be qualified for the particular use or installation in each rotorcraft type
design. A dynamic test may be required for alternate restraint systems as well as the
originally approved system. TSO C114 approval does not constitute approval for
installation of a restraint system in a rotorcraft design subject to dynamic test.

                  (i)   Paragraph 27.562 of this AC concerns in part the dynamic test
standards of Amendment 27-25.

                   (ii)  AC 23-4 dated June 20, 1986, concerns static test procedures for
small airplane seats and restraint systems. (Certain small airplanes manufactured after
December 12, 1986, should have harnesses for each seat also.) A test proposal for
rotorcraft installations may adopt procedures appropriate to the particular installation.
The 60/40 percent distribution is sufficiently achieved when the blocks in Figure 4 of
AC 23-4 are used.

                    (iii)  The static design side load for the harness installation may be proven
by test or analysis using the load distribution previously noted. For “older” designs, the
side load of § 27.561(b)(3)(iii) is 2.0g, and for later designs (Amendment 27-25 and
later), it is 8.0g.





                                                        Page A - 3

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →