FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 781

PDF page 781 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 781
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 7                                                       2/4/2016


             (iv) Plugs and Cables. Connector pins for sensitive signal circuits should not
be adjacent to pins used for ac power circuits.  If redundant wiring is used to comply
with systems regulations such as § 27.1309, the wires should be routed through
separate plugs or cables with as much physical separation as practicable. The system
design should eliminate possible incorrect mating of plugs. Minimize electromagnetic
interference by using cable grounding and shielding techniques.

       (4) System Performance. Where the operating or airworthiness regulations
require a system to perform its intended function, and when the equipment is not
qualified by TSO or other approval means, performance data furnished to the
FAA/AUTHORITY can reduce the installed performance testing. The appropriate TSO
minimum performance standard may be useful as a guide.

               (i) Environment. An appropriate means for environmental testing is set forth
in Radio Technical Commission for Aeronautics (RTCA) Document DO-160. Applicants
should submit test reports showing that the laboratory-tested categories, such as
temperature, vibration, altitude, etc., are compatible with the environmental demands
placed on the rotorcraft.

                (ii) Failure Analysis. Section 27.1309(b) requires consideration of system
malfunctions or failures.

       (5) Installation Design.

               (i) Mechanical Installation. Installations should ensure compliance with
airworthiness regulations and comply with the equipment manufacturer’s
recommendations. The designer should observe good engineering practices in
specifying material type, thickness, fastener type, edge distance, and attachment to the
equipment rack. By analysis or static tests, the mounted equipment should be shown to
withstand the inertia forces of §§ 27.561(b)(3) and 27.337. Refer to AC 43.13-2 (current
version) for static test procedures.

                (ii) Arrangement and Visibility. The mounting position of all instruments,
switches, position labels, and control heads should make them plainly visible to the pilot
while in his normal, panel-facing position and under all cockpit lighting conditions likely
to occur. TSO approval does not assure instruments will be acceptable in a particular
cockpit installation or for all lighting conditions. The instruments, switches, and
placarding must be free from reflections. Malfunction annunciation devices should be
conspicuous and clearly visible to the pilot. (See §§ 27.1321, 27.771, 27.1381,
27.1555(a) and AC 20-69.)

                 (iii) Load Analysis.

              (A) Power sources.  It should be determined whether the electrical power
source capacity is adequate for the system installation under all foreseeable operating
conditions including engine failure on multiengine rotorcraft. Apply system load


Page MG 1 -2

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →