FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 782

PDF page 782 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 782
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/4/2016                                      AC 27-1B, Chg 7


reductions or increase power source capacity, if necessary, to assure compatibility
between load and source.  If duplicate systems are required, power them from separate
buses.

              (B) Navigation course deviation circuit loading.  It should be determined
that its load matches the impedance of the deviation circuit source and does not exceed
the source capacity. Consider the transfer loads when the system is capable of transfer
(§ 27.1301).

             (C) Malfunction indicator circuit loading.  It should be determined that its
load matches the impedance of the malfunction indicator source and does not exceed
the source capacity. Consider the transfer loads when the system is capable of transfer
(§ 27.1301).

             (D) Synchro signal loading. When adding parallel loads to synchros,
review the manufacturers’ specifications to assure that the additional loads do not result
in an overloaded synchro.

             (iv) Interface. In many cases, different manufacturers design the mating units
of a system. For example, a brand-X gyro may be designed for operation with a
brand-X flight director, but later a modifier decides to operate a brand-Y autopilot with
the brand-X gyro. This applies just as well to navigational (NAV) receivers, Area NAV
(RNAV) units, course indicators, omni bearing selectors, tachometer indicators,
transmitters, and many other equipment items. When this is the case, the applicant
should provide data, in summarized form, describing those characteristics such as
impedance, volts, etc., that are necessary to ensure a compatible and reliable system.
The data should also reference the source of the interface data (§ 27.1301).

            (v) Flight Tests. An FAA/AUTHORITY engineering flight test is required
during type certification or after modification that changes the established limitations,
flight characteristics, or performance of a rotorcraft or any of its required systems or
operating procedures. Appropriate flight test personnel should evaluate new
installations of equipment in the cockpit or modifications that affect existing equipment
in the cockpit, if it is necessary to evaluate operational aspects of the change.  If the
applicant opts to darken the windows, evaluate the cockpit arrangement, placards,
markings, instrument visibility, and light reflections on the ground, where possible.
Conduct electromagnetic compatibility functional checks, windshield glare, and pilot
workload evaluations in flight at the FAA/AUTHORITY flight test pilot’s option.

             (vi) Radio Master Switches. Some installations incorporate radio master
switches to control special busses for the avionics systems.  If providing this capability,
evaluate it to ensure no introduction of failure modes that will result in excessive or even
total loss of all required avionics. One switch that controls all required avionics is
unacceptable for instrument flight rules (IFR) installations. The evaluation should
include an assessment of the loss of the systems to be included on the radio master
switch(es), and the subsequent effect on continued safe flight.


                                                        Page MG 1 -3

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →