FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 973

PDF page 973 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 973
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/4/2016                                                  AC 27-1B, Chg 7



        (11) NVIS cockpit and NVG integration.

                  (i) Accessibility and workload.

                (A) The NVIS configuration should not compromise the ability to perform all necessary
duties. Consider scanning and control accessibility. The applicant should determine the representative
flight profiles and environmental conditions under which the workload should be evaluated. The purpose
of this evaluation is to ensure that the workload associated with NVIS operations does not compromise
safety of flight.  It is important to assess the lighting system’s support of transition from aided flight to
unaided flight. Demonstrate compliance with §§ 27.771, 27.773, 27.777, and 27.1523. Carefully
consider the installation suitability for single pilot operation taking into account workload, cross cockpit
view, and reduced field of view with the consequent need for greater head movement.

                (B) If taking credit for the use of the landing light, this should be selectable and
controllable without removing either hand from the primary flying controls.

                (C) The design of the NVIS should consider flight into inadvertent IMC, unusual attitude
recovery, and the transition from aided flight to instrument flight. This will also address the consequences
of loss of external view through the NVG. Therefore, the applicant should plan this evaluation during all
phases of aided flight (such as cruise flight or takeoff and landing, if requested) to ensure that workload is
acceptable and the required instruments are within the pilot’s primary scan.

                (D) Assess the NVIS lighting for readability, uniformity, balance, light leakage, reflections,
and degradation of NVG performance. See the NVIS and NVG cockpit integration checklists at
http://www.faa.gov/aircraft/air_cert/design_approvals/rotorcraft/nvis/. In addition, RTCA Document
DO-275, section 4.0, provides an expanded explanation. Assess the cockpit using the make, model, and
part number of the NVG that the applicant intends to show that are compatible with their NVIS lighting
system.

                    (ii) Controls.

                (A) Accessibility of NVIS lighting system controls. Pilots should be able to readily identify,
access, and operate, with one hand, the NVIS lighting controls in-flight from their normal seated position.

                (B) Inadvertent actuation of controls. Provide appropriate protection to prevent the
inadvertent actuation of NVIS lighting controls and non-NVIS light sources.

                     (iii) Visibility.

                (A) Windshield. The windshield and transparencies should not decrease NVG light
sensitivities more than 12% (equivalent to one resolution element on a tri-bar chart).  If the aircraft has a
windshield anti-ice function, the visibility should be evaluated with anti-icing on and off to assess effect on
the NVGs. Operation of windshield anti-ice should follow manufacturer’s procedures and limitations.

                (B) Glare and reflectivity. Internal and external light sources can produce glare and
reflectivity.

                (C) Internal light sources.
                      (1)- Reflections should be no worse than the original unaided lighting. However,NVGs may pick up more reflections than seen with unaided vision. Additionally, NVIS-incompatible light
sources in other areas of the aircraft can cause interference. Block those reflections to ensure they do
not interfere with the pilot’s ability to see outside the aircraft while wearing NVGs.




                                                                     Page MG 16-9

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →