Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
2/12/03 AC 27-1B, Chg 1
(4) Controlled Introduction to Service.
(i) For some credit applications, full validation and implementation may
be possible during the development period. However, for many HUMS techniques, a
plan for a controlled introduction to service may be necessary to fully validate the credit.
(ii) There must be provisions in the certification process to instruct the
continued airworthiness effort to ensure compliance with the aforementioned plan.
(iii) During the implementation of this plan, data is accumulated by
operational aircraft, and from this data, refinements and adjustments to the original
criteria can be made. This period may also allow a proposed credit to be operated in
parallel with alternative or standard procedures when it is necessary to gain additional
in-service validation by way of back-to-back comparison
(iv) The plan should include procedures and provisions for this controlled
period and should include clear goals by which progress and ultimately termination of
this phase can be measured. The plan may include a multi-credit HUMS that will
require a phased introduction of credits.
(5) Continued Airworthiness and Synthesis of Credit. Normal and established
procedures will prevail for HUMS as for all other continued airworthiness matters.
Arrangements should be made to validate the performance of an approved credit
throughout its service use. Provisions should be made to allow for the synthesis of the
service experience with relevant engineering evidence from rejected components,
development testing, seeded testing, etc. Any necessary or desired modifications to the
HUMS application or the component/equipment being monitored must be re-evaluated.
h. Instructions for Continued Airworthiness (ICA) and Other Requirements for
Health and Usage Monitoring System (HUMS). This section addresses the ICA,
operator's HUMS program, HUMS training, and Master Minimum Equipment List
(MMEL) revision to incorporate HUMS.
(1) Instructions for Continued Airworthiness. The applicant for HUMS is
required to provide ICA developed in accordance with FAR/JAR Part 27 and Appendix
A. This section provides supplemental guidance with addressing aspects unique to
HUMS. The applicant may be an airframe manufacturer, HUMS equipment
manufacturer, or an operator. The ICA should address HUMS integration with the
aircraft. This section addresses both airborne and ground based systems and
equipment.
(i) HUMS ICA Items. The applicant must address the following subjects
in addition to FAR/JAR Part 27. These subjects should address both airborne and
ground based systems and equipment unless specifically indicated otherwise.
Page MG 15 - 15
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.