Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 9/17/2009
(1) Instrumentation/Equipment. Aircraft instrumentation may include engine
and flight parameters, control positions, power lever position, and landing gear loads. A
record of rotor RPM at touchdown is necessary to assure it does not exceed transient
limits. Rotor RPM at touchdown may be lower than the minimum transient limit for
flight, provided stress limits are not exceeded. A crash recovery team with the support
of a fire engine is highly desirable.
(2) The OEI landing is similar in many respects to the Height-Velocity (HV)
tests described in AC 27.79 of this advisory circular. Most of the comments, cautions,
and techniques for HV also apply here, even though the typical flight conditions are less
critical than limiting HV points due to a lower power level and an established rate of
descent. The approach is made at a predetermined speed with OEI. The speed is
reduced and the rotorcraft is flared to a conventional OEI landing. To show compliance,
full OEI landing should be demonstrated from sea level to the maximum altitude
capability of the rotorcraft or 7,000 feet, whichever is less, at the maximum landing
weight, without damage. For altitudes above 7,000 feet to the maximum takeoff and
landing altitude, compliance with this requirement is shown by demonstrating that the
OEI descent rate and forward speed can be reasonably controlled.
(3) Power. Power should be limited to minimum specification values on the
operating engine(s). This may be accomplished by adjustment of engine topping to
minimum specification values for the range of the atmospheric variables to be approved.
This is frequently done by installing an adjustable device in the throttle linkage with a
control in the cockpit so that engine topping can be accurately adjusted for varying
ambient conditions. With such a device in the control system, it becomes vitally
important to check topping power prior to each test sequence.
(4) Aircraft Loading. Aft CG is usually the most critical because visibility
constraints limit the degree to which the pilot can see the landing surface during the
flare. If a weight effect is shown, a minimum of two weights should be flown at each test
altitude. One weight should be the maximum weight for prevailing conditions, and the
other should provide a sufficient spread to validate weight accountability.
(5) All-engine-out landing.
(i) Several procedures can be utilized to demonstrate compliance with the
all-engine-out landing requirement of § 27.75(a)(1) and § 27.75(b). These paragraphs
contain two separate requirements. One is the ability to transition safely into
autorotation after failure of the last operative engine. The second aspect of this rule
requires that a landing from autorotation be possible. The second requirement is
discussed below. The maneuver is entered by smoothly reducing power at an optimum
autorotation airspeed at a safe height above the landing surface. Typically a full
autorotation landing to touchdown is demonstrated at sea level standard day for the
maximum landing gross weight for that altitude. For altitudes above standard sea level,
Page 36
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.