Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 1 2/12/03
(1) Applications providing cockpit warning(s) which are the only means of
detection with associated flight manual instructions to land immediately.
(2) System applications, for which constantly misleading information
could be assessed as leading to a Catastrophic condition, must be designed to either
detect these errors (e.g. Built-In-Test, system redundancy, etc.) and/or be tolerant to
these errors (i.e., procedural, etc.).
(D) The Functional Hazard Assessment (FHA) may be a preliminary
document to the Preliminary Safety Assessment (PSA) or a part of the PSA. The FHA
is a top down analysis (which should involve pilots and flight analysts as well as
engineers) that starts with the hazards to the rotorcraft and traces these hazards to the
system, subsystem, and component level in the areas affected by HUMS. This type of
analysis starts with the determination of what undesirable effects can occur as a direct
or indirect result of using HUMS for maintenance or operational actions. The level of
severity associated with this effect will result in assigning a criticality level that uses the
definitions of criticality contained herein.
(E) The final level of equipment qualification may not only be the result of
technical considerations, but also of other mitigating actions, of which there are many
types. Many of these actions can result in a reduction of qualification levels for
equipment.
(ii) Mitigating Actions.
(A) A mitigating action is an autonomous and continuing compensating
factor which may modify the level of qualification associated with certification of a
HUMS application. These actions are often performed as part of continued
airworthiness considerations and are also an integral part of the certification. As such,
the continuation of certification limitations, where appropriate, must be included in the
Instructions for Continued Airworthiness (ICA). Mitigating actions are subjective in
nature and are an intended method(s) of application where the pre-mitigated levels of
integrity are defined.
(B) Applications that use COTS software and therefore may not be fully
qualified applying RTCA/DO-178/ED-12 methodology may be accepted by alternative
qualification methods as stated in paragraph f(3). Therefore, the subsequent use of
mitigating actions that are of themselves of a subjective nature should be approached
with caution. A mitigating action must be based upon the integrity level derived from the
FHA.
(C) If the mitigating action is an operational consideration, the same
concerns apply for continuing the mitigating action. The mitigating action should be
recorded in the certification limitations and in the approved flight manual.
Page MG 15 - 6
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.