Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 3/31/2014
The speed is reduced and the rotorcraft is flared to a conventional
one-engine-inoperative landing.
(3) Power. Power should be limited to minimum specification values on the
operating engine(s). This may be accomplished by adjustment of engine topping to
minimum specification values for the range of atmospheric variables to be approved.
This is frequently done by installing an adjustable device in the throttle linkage with a
control in the cockpit so that engine topping can be accurately adjusted for varying
ambient conditions. With such a device in the control system it becomes vitally
important to check topping power prior to each test sequence.
(4) Aircraft Loading. Aft center of gravity is usually most critical because
visibility constraints limit the degree to which the pilot can see the landing surface during
the flare. If a weight effect is shown, a minimum of two weights should be flown at each
test altitude. One weight should be the maximum weight for prevailing conditions, and
the other should provide a sufficient spread to validate weight accountability.
(5) All-engine-out landing.
(i) Several procedures can be utilized to demonstrate compliance with
the all-engine-out landing requirement. As discussed in the explanation portion of this
paragraph, § 27.75(b) contains two separate requirements. One is the ability to
transition safely into autorotation after failure of the last operative engine. The second
aspect of this rule requires that a landing from autorotation be possible. The second
requirement is discussed below. The maneuver is entered by smoothly reducing power
at an optimum autorotation airspeed at a safe height above the landing surface. If a
complete company test program has documented an all-engine-out landing to the GW/σ
(gross weight/density ratio) limit, verification tests may be initiated at those limiting
weight conditions. If not, buildup testing should be initiated at light weight. This test is
ordinarily conducted at mid center of gravity. Typically, all altitudes may be approved
with two weight limit landings-one at sea level and one near maximum takeoff and
landing altitude.
(ii) Demonstrated compliance with this requirement is intended to show
that an autorotative descent rate can be arrested, and forward speed at touchdown can
be controlled to a reasonable value (less than 40 KTAS is recommended) to ensure a
reasonable chance of survivability for the all engine failure condition. On multiengine
rotorcraft, rotor inertia is typically lower than for single-engine rotorcraft. RPM decays
rapidly when the last engine is made inoperative. Due to this relatively low inertia level,
considerable collective may be needed to prevent rotor overspeed conditions when the
rotorcraft is flared for landing. Also, when testing the final maximum weight points, the
pilot should anticipate a need for considerable collective pitch to control rotor overspeed
during autorotative descent, particularly at high altitude WAT limiting conditions. Some
designs incorporate features which may lead to rotorcraft damage in testing this
Page 34.2
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.