FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page B-34.1

PDF page 93 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 93
AC 27-1B · B-34.1Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

3/31/2014                                      AC 27-1B, Chg 4


AC 27.75. § 27.75 (Amendment 27-14) LANDING.

     a. Explanation.

         (1) This rule incorporates all of the landing requirements for Part 27 rotorcraft.

         (2) As with other flight maneuvers, landings must be accomplished with
acceptable flight and ground characteristics using normal pilot skills. Reasonable
sampling and extrapolation methods are, of course, allowed. General guidance on
those subjects is given in paragraph AC 27.45. As in other performance areas, engines
must be operated within approved limits.

         (3) Landing. Approach and landing path requirements are stated in general
terms in paragraphs (a)(1) and (a)(2) of § 27.75. The approach path must allow smooth
transition for a one-engine-inoperative landing and adequate clearance from potentially
hazardous HV combinations.

         (4) All-engine-out landing. Section 27.75(b) contains the certification
requirement for “last” engine failure and all-engines-inoperative landing. The rule states
that it must be possible to make a safe landing after complete power failure during
normal cruise.  It is not intended that all engines be failed simultaneously, although
complete power failure has occurred in twin-engine rotorcraft with Category A engine
isolation. This requirement assures that in the event of cockpit mismanagement, fuel
exhaustion, improper maintenance, fuel contamination, or unforeseen mechanical
failures, a safe autorotation entry can be made and a safe power-off landing can be
affected. Two separate aspects of this rule are normally evaluated at different times
during the test program. The “last” engine failure is normally evaluated during cruise or
VNE engine failure testing where instrumentation and critical loading have been
established for those test conditions. The all-engine-out landing is ordinarily conducted
in conjunction with an HV or landing distance phase where ground instrumentation and
safety equipment are available.

     b. Procedures.

         (1) Instrumentation/Equipment. Aircraft instrumentation may include engine
and flight parameters, control positions, power lever position, and landing gear loads. A
record of rotor RPM at touchdown is necessary to assure it does not exceed transient
limits. Rotor RPM at touchdown may be lower than the minimum transient limit for
flight, provided stress limits are not exceeded. A crash recovery team with the support
of a fire engine is highly desirable.

         (2) The one-engine-inoperative landing is similar in many respects to the HV
tests described in paragraph AC 27.79. Most of the comments, cautions, and
techniques for HV also apply here even though the typical flight conditions are less
critical than limiting HV points due to a lower power level and an established rate of
descent. The approach is made at a predetermined speed with one engine inoperative.


                                                         Page B -34.1

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →