FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page B-34

PDF page 92 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 92
AC 27-1B · B-34Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

As a technique, it is recommended the rotorcraft be loaded to a center of gravity near
the hook to minimize fuselage angle changes with varying powers.  All tethered hover
data should be verified by a limited spotcheck using the free flight technique. The free
flight technique as contained in paragraph AC 27.73b(4) will determine if any problems,
such as load cell malfunctions, have occurred. The free flight hover data must fall within
the allowable scatter of the tethered data.

         (4) If there are no provisions or equipment to conduct tethered hover tests, the
free flight technique is also a valid method. The disadvantage of this technique as the
primary source of data acquisition is that it is very time consuming. In addition a certain
element of safety is lost OGE in the event of an emergency. The rotorcraft must be
reballasted to different weights to allow the maximum Ct/Cp spread. When using the
free flight technique, either as a primary data source or to substantiate the tethered
technique, the same considerations for wind, recorded parameters, etc., as used in the
tethered technique apply. Free flight hover tests should be conducted at CG extremes
to verify any CG effects.  If the rotorcraft has any stability augmentation system which
may influence hover performance, it must be accounted for.

         (5) It is extremely difficult to determine when a rotorcraft is hovering OGE at
high altitudes above ground level since there is no ground reference. In a true hover,
the rotorcraft will drift with the wind. Numerous techniques have been tried to allow
OGE hover data acquisition at high altitudes, all of which have resulted in much data
scatter. Until a method is proposed and found acceptable to the FAA/AUTHORITY,
OGE hover data must be obtained at the various altitude sites where IGE hover data
are obtained. Hover performance can usually be extrapolated up to a maximum of
4,000 feet.





Page B - 34

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →