FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page B-33

PDF page 91 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 91
AC 27-1B · B-33Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

gross weight. The rotorcraft will be stabilized at a fixed power setting and rotor speed at
the appropriate skid or wheel height. Once the required data are obtained, power
should be varied from the minimum to the maximum allowed at various rotor RPM. This
technique will produce a large Ct/Cp spread. The load cell reading is recorded for each
stabilized point. The total thrust the rotor produces is equal to the rotorcraft’s gross
weight plus the weight of the cables and load cell plus cable tension. Care must be
taken that the cable tension does not exceed the cargo hook limit or load capacity of the
tie-down. For some rotorcraft, it may be necessary to ballast the rotorcraft to a heavy
weight in order to record high power hover data.

         (2) The pilot maintains the rotorcraft in position so that the cables and load cell
are perpendicular to the ground. To ensure the cable is vertical, two outside observers,
one forward of the rotorcraft and one to one side, can be used. Either hand signals or
radio can be used to direct the pilot. The observers should be provided with protective
equipment. Positioning can also be accomplished by attaching two accelerometers to
the load cell which sense angle or movement along the longitudinal and lateral axes.
Any displacement of the load cell will be reflected on instrumentation in the cockpit, and
by reference to this instrumentation, the rotorcraft can be maintained in the correct
position. Increased caution should be utilized as tethered hover heights are decreased
because the rotorcraft may become more difficult to control precisely. The tethered
hover technique is especially useful for OGE hover performance data because the
rotorcraft’s internal weight is low and the cable and load cell can be jettisoned in the
event of an engine failure or other emergency.

         (3) To obtain consistent data, the wind velocity should be less than 3 knots as
there are no accurate methods of correcting hover data for wind effects. Rotorcraft with
high downwash velocities may tolerate higher wind velocities. The parameters usually
recorded at each stabilized condition are:

                  (i)   Engine torque.

                   (ii)   Rotor speed.

                    (iii)  Ambient temperatures.

               (iv)  Pressure altitude.

              (v)   Fuel used (or remaining).

               (vi)  Load cell reading.

                (vii)  Generator(s) load.

                 (viii) Wind speed and direction.




                                                       Page B - 33

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →