FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 916

PDF page 916 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 916
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 1                                                           2/12/03

                  (i)   Cracks emanating from the edge of structural openings or cutouts
which can be readily detected by visual inspection of the area.

                   (ii)  A circumferential or longitudinal skin crack in the basic fuselage
structure of such a length that it can be readily detected by a visual inspection of the
surface area.

                    (iii)  Complete severance of interior frame elements or stiffeners in addition
to a visually detectable crack in the adjacent skin.

               (iv)   Failure of one element in a multiple load path design.

              (v)   Failure of primary attachments, including control hinges and fittings.

         (3) Determination of Probable Crack Locations. The probable crack locations
are to be determined by tests, analysis, or both. In cases of unusually critical or
complex components or when initial fatigue loading may affect the rate or mode of
cracking, the probable crack locations should be determined by fatigue test. When
determination is made by analysis, sound engineering judgement should be used and a
variety of factors such as the following should be taken into account:

                  (i)   Conducting an analysis to locate areas of maximum stress and low
margin of safety.

                   (ii)   Conducting strain surveys on undamaged structure to establish points
of high stress concentration as well as the magnitude of such concentration.

                    (iii)  Examining static test results to determine locations where excessive
deformation occurred.

               (iv)  Determining from fatigue analysis where cracks may initiate.

               (iv)   Selecting locations in an element where the stresses in adjacent
elements would be the maximum with that element failed.

              (v)   Selecting partial fracture locations in an element wherein high stress
concentrations are present in the residual structure.

               (vi)  Assessing design detail areas which are prone to fatigue damage
such as joints, holes, and other features as based on service and test experience of
similarly designed components.

         (4) Fail-Safe Demonstration.  It is to be demonstrated by analysis, tests, or
both, that the structure with the partial failures as defined in paragraphs f(2) and f(3) can
withstand the maximum load and the repeated loads expected in service during the
period prior to detection. The repeated loads should be as defined in the loading


Page MG 11 - 14

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →