Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
2/12/03 AC 27-1B, Chg 1
fatigue behavior should be well established for each application. It is important to apply
the chosen method consistently and should any of the analyses identify the need for a
replacement time, testing should be conducted to support the assumptions made. The
certifying authority should approve these rational methods.
(3) Testing Methods. The fatigue strength of the flight structure may be
determined in appropriate laboratory tests and evaluated in terms of the loading
spectrum. The mean strength indicated by the test results should be reduced by a
factor or factors such that the probability of occurrence of a lower strength part in
service is very low. This conservative treatment of strength combined with a
conservative treatment of both the flight loads (paragraph c.) and their frequency of
occurrence (paragraph d.) must assure that the probability of failure is extremely
remote. All test articles should be fully representative of the design standard selected
for evaluation, including the processes used in manufacture. The test fixture should be
capable of applying the loading conditions in a way that loads the component in the
same manner as when on the rotorcraft. The test loads developed in the component
should be correlated with those measured in the flight load survey.
(i) S/N Curves. Constant amplitude fatigue tests should be conducted to
define the mean strength. Whenever possible several S/N data points should be
established for each of a number of different alternating load levels. The fatigue tests
should be performed at mean stresses or loads representative of those occurring in
flight. In addition, some components subjected to both dynamic and low cycle loading,
for example a main rotor blade, may require the addition of a start-stop or GAG cycle
testing, and the resulting fatigue damage included in the component life determination.
In order to determine the mean fatigue strength, it is necessary to test actual
components. These tests will allow the construction of the mean S/N curve when
combined with an established curve shape. The S/N curve shape may be derived by
using a least square fit curve through coupon data or appropriate published material
data. Care should be taken in the selection of curve shape, particularly when fretting is
present. Then, to account for fatigue strength variability, the mean curve must be
reduced to a working curve. In establishing the working curve, consideration should be
given to the number of specimens tested, the variability of the fatigue results, previous
test data on the same material or similar components, as well as service experience. At
least four full-scale specimens are recommended, but fewer may be adequate in
association with a conservative approach to establishing the working curve considering
the reduction in reliability this infers. Current practice shows that when four or more
specimens are used, the resulting working curve (Figure AC 27.MG 11-5) can range
from 51% to 70% of the mean curve in strength for aluminum alloys and 56% to 75% for
steels. The successful application of the resulting working curves will depend on the
degree of conservatism shown in the flight loads and occurrence spectra. Therefore it
follows that use of the least conservative of these working curves would necessitate the
greatest conservatism in the flight loads and assumptions relating to likely operational
use. Consideration should also be given to fatigue life reduction factors when
constructing the working curve. Typical factors range from around four to ten at less
than 100,000 cycles. It may be possible to determine reduction factors from a large
AC Page MG 11 - 11
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.