FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 911

PDF page 911 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 911
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/12/03                                        AC 27-1B, Chg 1

of reliability and safety as obtained with a full scale test approach. However, in many
cases the differences between past test specimens and the actual part (which involve
such factors as stress concentration, size, and fretting) cannot be accounted for with a
reasonable degree of accuracy. Therefore, it is usually necessary that the structural
components be subjected to repeated load tests using information determined in the
flight load measurement program. Special operational or functional characteristics that
could affect the fatigue strength should also be considered in the service life evaluation.
Such factors as high blade operating temperatures due to tip jets or turbine exhaust
impingement on the tail rotor should be considered as well as other special operating
conditions. In addition, effects of special purpose use such as hoist and external
operation, spraying, surveying, etc., should be considered if appropriate to the particular
type. The fatigue strength may be evaluated using the methods outlined below, of
which full scale testing is the preferred method.

         (2) Analytical Methods

                  (i)    Simplified method. This method requires that an operating boundary
for stress levels be established. The following techniques that account for the effects of
cyclic and steady stresses are considered acceptable for establishing the allowable
stress levels:

              (A) The mean endurance limit of the part should first be estimated from
simple material test specimens. The test specimen material should be representative of
the actual part and sufficient test data should be available to substantiate a mean
endurance limit (the reference specimen endurance limit, Line AD of Figure
AC 27.MG 11-4). A range of cycles from 107 to 109 may be appropriate to estimate the
endurance limit dependent on the material. The estimate should account for surface
conditions, fabrication methods, fretting, size and shape effects, and environmental
conditions, as well as differences in stress concentrations between the test specimen
and the actual part. Referring to Figure AC 27.MG 11-4, the endurance limit of the part
may be represented by a straight line drawn through the yield stress (point D on the
horizontal axis) and the mean endurance limit from test results, suitably adjusted to
account for the considerations detailed above, at a given steady stress. The
intersection of this line with the vertical axis is point B. This produces the adjusted
specimen endurance limit, line BD.

              (B) A factor or safety of 3 should then be applied to the adjusted
specimen endurance limit so that the slope of line CD (the operating boundary) would
be 1/3 of line BD.

             (C)  If all operating stress cycles fall below the operating boundary line
(CD), no fatigue testing is necessary. When any of these stresses are above the
operating boundary line, fatigue testing of the actual parts should be conducted, unless
a suitably conservative approach such as that outlined in d(4)(ii) is adopted.




                                           AC Page MG 11 - 9

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →