Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 1 2/12/03
However, it may be possible to adjust replacement times by counting events or by
factoring flight hours for certain types of operation. Any such procedure will require the
approval of the certification authority for a suitably amended airworthiness limitation
section and should also consider the operational aspects involved. For example, a
component where significant damage occurs during the GAG or power cycle may more
appropriately be assigned a life in terms of the number of cycles of takeoffs or lifts in
lieu of tracking flight time in hours. The cycles should be properly defined and related to
events that are easily identified and recorded by the crew or by an approved usage
monitor (e.g., takeoffs or lifts). This example procedure would retire the component
sooner when it is used in an external load operation mission involving many cycles per
flight hour. Conversely, an operator performing a less severe operation standard
mission could leave the component in service longer since fewer cycles are
accumulated. This procedure would permit the rotorcraft to be used for different types
of operations and still ensure a safe replacement time for the component.
(ii) Where appropriate, some of the basic usage assumptions made in the
fatigue evaluation which the operator can reliably assess (such as numbers of ground
air ground cycles) should be noted in the airworthiness limitations section of the
maintenance manual. The intent of this would be to make operators aware of these
criteria so that appropriate actions may be taken.
(iii) Should subsequent usage of the rotorcraft encompass an operation
for which the original structural substantiation did not account, the effects of this new
operation should be addressed, and in the interests of safety, a reassessment made.
Subsequently, if the replacement times require revision, those new times may be limited
to aircraft involved in the new operation provided:
(A) Proper part re-identification is established;
(B) a rotorcraft flight manual supplement outlining limitations is approved;
(C) an airworthiness limitations section supplement is approved; (this is
also required for incorporation of new methods for managing replacement times, see
paragraph d4(i) above); or,
(D) a combination of the above.
e. Fatigue Life Evaluation.
(1) General. Information for fatigue evaluation based on safe-life
considerations leading to replacement times is provided in this section. Although there
is a large quantity of information available on the fatigue strength characteristics of
material specimens, built-up specimens and parts, the prediction of the strength of parts
of new designs based on this information is less accurate than testing the actual part.
Consequently, for an analysis based on test data other than the actual part to be
considered acceptable, additional conservatism should be used to achieve similar levels
Page MG 11 - 8
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.