FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 908

PDF page 908 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 908
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 1                                                           2/12/03

components, typical flight conditions to evaluate include, but not limited to: spot turns in
hovering, sideward flight or level flight with sideslip. In order to account for data scatter
and to determine the load/ stress levels present, a sufficient amount of data points
should be obtained at each flight condition. In some instances, the critical weight,
center of gravity, and altitude cases for the various maneuvers can be based on
validated flight loads analysis or on past experience with similar designs. This
procedure is acceptable where adequate flight tests are performed to substantiate such
selections. The combinations of flight parameters that produce the most critical
load/stress levels should be included in the fatigue evaluation. In addition attention
should be paid to the influence of temperature through the whole range certified,
especially to very cold temperature (typically below -30°C [= -20°F]). For example, the
characteristics of elastomeric components in rotor assemblies are particularly sensitive
to temperature change. This influence can be evaluated either in flight during a cold
weather campaign or by analysis based on elastomer characteristics such as stiffness
and damping measured in a cold temperature chamber.

     d. Frequency of Occurrence (Usage) Spectrum.

         (1) General. The frequency of occurrence spectrum (often called usage
spectrum) defines the maneuvers the rotorcraft will perform in the various types of
operation, and the percentage time or number of events associated with each
maneuver. The diversity of rotorcraft sizes and speed together with the wide range of
passenger/cargo capability requires that a comprehensive evaluation of each possible
mission scenario be accomplished for each rotorcraft model. Some of the most
common types of operation include transport, offshore support, traffic reporting,
emergency medical services (EMS), law enforcement, search and rescue, agricultural
spraying and external sling operation. Each of these operations has unique
requirements in terms of maneuvers, gross weight/center of gravity and altitude.
However, each helicopter model may fly one or more of these operations throughout its
operational lifetime. Replacement times should account for the worst case operation for
each component, unless a method approved by the Authorities is developed which
allows consideration of multiple type of operations by factoring hours or counting
events.

         (2) Spectrum Development. The frequency of occurrence spectrum should be
based on information that is applicable to the mission(s) the rotorcraft is to perform. All
damage that is likely to occur in actual usage should be accounted for including low
cycle damage from power cycles and the ground-air-ground (GAG) cycle. This
information may come from direct measurement of usage data from the same or similar
rotorcraft, usage monitors, questionnaires or direct observation of the helicopter
performing the mission. Design limitations established in compliance with §§ 27.309 or
29.309 and any recommended operating conditions and limitations established and
specified in the rotorcraft flight manual should also be reflected in the spectrum. An
example of a twin turbine spectrum is presented in Figure AC 27.MG 11-9. This table
should be used only as a guide and should be modified as necessary for each particular
rotorcraft. An example of the diversity in the frequency of occurrence spectrum is


Page MG 11 - 6

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →