FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 907

PDF page 907 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 907
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/12/03                                        AC 27-1B, Chg 1

off operation. For heavy lift and external-lift helicopters the loaded and unloaded
conditions of operation should be investigated in conjunction with other important
parameters. When the mission being evaluated involves the use of a long line, the flight
strain survey should be flown with a long line. This will insure that the correct rotor and
control loading will be duplicated particularly in hover and low speed maneuvers since
the c.g. offset, drag, and inertia effect of the external load can be a factor in dynamic
loads. Generally the VNE when performing external cargo missions is reduced because
of safety or other reasons. In addition, for these uses, and others where the operation
requires frequent excursions to the proposed limitations of the rotorcraft, reasonable
consideration should be given to unintentional exceedences and the development of
these limits. The extent of the assessment would generally be founded on experience,
but also acknowledging tolerances in instrumentation and the circumstances of the
operation, particularly the level and focus of pilot workload. Similarly the effects of
structurally significant maintenance should be investigated as necessary, particularly
where unusually large load amplifications could be expected as a consequence and the
probability of occurrence is shown or believed to be substantial based on experience.
Operating limitations and maintenance instructions may be adjusted on the basis of
these investigations. For all rotorcraft the effects of ground operation should be
investigated. The ground and flight conditions to be investigated should be submitted
as part of with the flight evaluation program.

                    (iii)  The severity of maneuvers investigated during the flight strain survey
should be such that it is extremely unlikely that service use will be more severe. In this
evaluation, flight replications should be investigated during the load survey so that
normal and expected variations in achieving the specific target flight test conditions are
accounted for.

               (iv)  The extremes of aerodynamic configuration, including operation with
doors off or open and simultaneous use of equipment, should be investigated as well as
the usual parameters. In addition, when the rotorcraft is equipped with externally
mounted devices such as rescue hoist, spotlight, camera, infrared sensors, etc. it is
necessary to evaluate the loads. These or similar devices can increase the profile drag
thus increasing power required. Additionally, the airflow from these devices can
impinge on the tail boom, fin or tail rotor altering the loads determined for the clean
aerodynamic configuration. When these devices are installed by a modifier as a
Supplemental Type Certificate (STC), it is the responsibility of the STC holder to
investigate any effects the device may have alone or in combination with other
externally mounted devices.

All flight conditions considered appropriate for the particular design are to be
investigated over the complete rotor speed, airspeed, longitudinal and lateral center of
gravity, altitude and weight (from minimum mission weight to maximum mission weight)
ranges to determine that the critical loads/stresses associated with each flight condition
are identified. Typical damaging flight conditions for main rotor components and
suspension include, but are not limited to: high speed flight, turns, pull-ups, sideward
flight, approach, autorotation, taxiing, take off and landing on slopes. For tail rotor


                                           AC Page MG 11 - 5

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →