Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 1 2/12/03
and end of a flight. Strain gauges should be temperature compensated where
necessary.
(iv) In the case of calibrated structure, rational evaluation of the calibration
rig procedure should be performed to demonstrate that strain-load response is
representative over the range of flight maneuvers and operational parameters that are
to be encountered. As a minimum, the calibration fidelity should address the loading
distributions applicable to the critical failure modes of the component under evaluation
and over a high percentage of the maximum expected flight load. Care should be taken
to ensure that any non-linear behavior is identified and properly considered.
(3) Parts Subject to Flight Measurement. Sufficient parameters of the rotor
systems, drive systems, control systems, fuselage, and supporting structure for rotors,
transmissions, engines, APU’s, and other dynamic components should be measured to
adequately define and substantiate the loading of these components. For rotorcraft of
unusual or unique design or operation or employing unusual equipment, special
consideration should be given to the unique features and also the effects they may have
on existing systems and structure.
(4) Flight Regimes and Operational Conditions to be Investigated.
(i) Typical flight and ground conditions to be investigated are given in
Figure AC 27.MG 11-7 for conventional passenger/utility use and additional conditions
in Figure AC 27.MG 11-8 for a lifting operation. For intensive lifting missions it should
be recognized that lifting conditions for both internal and external loads should be
investigated including landing with and without load as applicable. Figures
AC 27.MG 11-2 and AC 27.MG 11-3 show flight regimes that should be investigated for
power-on and power-off operation for all helicopters. Parameters, which define these
regimes, are included in these figures. Other parameters such as Gross Weight and
C.G. apply and should be included. The effects of temperature and of high altitude
operation or altitude cycling should be investigated. As noted on Figure
AC 27.MG 11-2, complete coverage at 111 percent VNE should be demonstrated for
power-on operation. However, for power-off operation, Figure AC 27.MG 11-3,
complete coverage at 111 percent VNE for maximum and minimum design RPM need
not be obtained if points are obtained at VNE at both maximum and minimum design
RPM and at 111 percent VNE at both maximum and minimum placarded RPM as
indicated in the figure. Conditions arising out of special requirements such as those
imposed by noise reduction and near surface operation should also be investigated.
(ii) The determination of the flight conditions to be investigated in the
flight strain measurement program should be based on the anticipated uses of the
helicopter. Information from similar designs and/or similar operations should be
assessed and used where applicable. Flight conditions considered appropriate for the
design and application must be representative of actual operation in accordance with
the rotorcraft flight manual. For multi-engine helicopters, the flight conditions
concerning engine out operations should be considered in addition to complete power-
Page MG 11 - 4
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.