Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
2/12/03 AC 27-1B, Chg 1
(iii) The frequency of occurrences associated with various flight conditions
and the corresponding spectrum of loading and stresses.
(iv) The fatigue characteristics of the structure, including fatigue strength,
and as necessary, crack propagation and residual strength characteristics.
c. Flight Load Measurement Program.
(1) General. Subsequent to design analysis, in which aircraft loads and
associated stresses are derived, the stress level and/or loads are to be verified by a
carefully controlled flight load measurement program. The flight load measurement
program shall demonstrate maximum and minimum loads for the entire flight envelope.
It shall also gather steady and cyclic load/strain data for use in the fatigue evaluation
required by §§ 27.571 and 29.571. The parameters to be measured are primarily load
calibrated strains supported by local strain measurement, accelerations, and deflections
as necessary.
(2) Instrumentation.
(i) The instrumentation system used in the flight parameter measurement
program should accurately measure and record the critical parameters under
operational test conditions. For critical maneuvers, the instrumentation should be
capable of recording data sequences for several related channels for stationary and
rotating channels. The location and distribution of the strain gauges should be based
on a rational evaluation of the critical stress areas. Appropriate analytical methods
should be used, such as Finite Element Modeling (FEM) and may be supplemented by
other techniques including strain sensitive coatings, photoelastic methods, and
thermography. Manual calculations based on the historical precedent of similar
structure can also be very helpful. As much as possible, the instrumentation plan
should standardize the gauge locations for each component so that all testing and other
experience can be related to the same common set of measurement parameters. The
gauge sensitivity, frequency response, location, distribution, and number of strain
gauges must provide the strain/load spectrum and strain/load distribution for each part
essential to the safe operation of the rotorcraft.
(ii) The corresponding flight and ground operation parameters (airspeed,
rotor RPM, center of gravity accelerations, etc.) should be recorded simultaneously and,
where appropriate, as time histories. This is necessary to correlate the loads and
stresses with the maneuver or operating condition during which they occurred. If the
number of data parameters required exceeds the system capability, enough “carry-over”
data channels should be included to reasonably relate all data for the specific maneuver
when several flights are necessary.
(iii) The instrumentation system should be adequately calibrated and
checked frequently during the strain survey. Ideally this would occur at the beginning
AC Page MG 11 - 3
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.