FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 900

PDF page 900 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 900
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99


         (2) The float system attachment hardware should be shown to be structurally
adequate to withstand critical air loads and water loads during water entry when both
deflated and stowed and fully inflated (unless in-flight inflation is prohibited). The
appropriate vertical loads and drag loads determined from water entry conditions (or as
limited by flight manual procedures) should be addressed. The effects of the vertical
loads and the drag loads may be considered separately for the analysis.

         (3) Flotation and Trim should be investigated for a range of sea states from
zero to the maximum selected by the applicant and should be satisfactory in waves
having height/length ratios of 1:12.5 for multi engine rotorcraft with Category A engine
isolation and 1:10 for all other rotorcraft.

                  (i)   Demonstrated to be satisfactory to at least sea state 4 water
conditions.

                   (ii)   Flotation tests should be investigated at the most critical rotorcraft
loading condition.

                    (iii)   Flotation time and trim requirements should be evaluated with a
simulated, ruptured deflation of the most critical float compartment. Flotation
characteristics should be satisfactory in this degraded mode to at least sea state 2
water conditions.

               (iv)  Probable rotorcraft door/window open or closed configurations and
probable damage to the airframe/hull (i.e., failure of doors, windows, skin, etc.) should
be considered when demonstrating compliance with the flotation and trim
requirements.

         (4) Float System Reliability. Reliability should be considered in the basic
design to ensure approximately equal inflation of the floats to preclude excessive yaw,
roll, or pitch in flight or in the water.

                  (i)   Maintenance procedures should not degrade the flotation system
(such as introducing contaminants which could affect normal operation, etc.).

                   (ii)   The flotation system design should preclude inadvertent damage due
to normal personnel traffic flow and excessive wear and tear. Protection covers should
be evaluated for function and reliability.

         (5) Buoyancy requirements for emergency flotation systems should be a
minimum of 25 percent excess buoyancy at maximum internal gross weight. The
weight of fresh water (density 62.42 lb/ft3) displaced by fully submerged float or floats
should be a minimum of 25 percent greater than the maximum certificated gross weight
of the rotorcraft. Analysis may be used for buoyancy verification.



Page MG 10 - 4

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →