Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
(6) Sufficient watertight compartments should provide an acceptable margin of
positive stability with any single main float compartment flooded or deflated. The
location of the floats, the most critical compartment, the rotorcraft weight, mass
moment of inertia, and center of gravity location are also important considerations for
stability. Analyses, tests, or a combination thereof may be used to substantiate a
positive margin of stability with the most critical compartment flooded or deflated.
(7) The inflatable bag type floats should be designed for the maximum
pressure differential developed at the maximum design altitude. That is, the resulting
pressure difference between an operational altitude and a take-off site elevation should
be established and substantiated. This resulting pressure differential may become an
operating limitation.
(8) The float landing load factors may be determined from the drop test of the
float landing gear or the loads may be derived from landing gear drop test or loads may
be determined from model or full scale water entry tests. The vertical loads are
distributed over three fourths of the bag's projected area. Bag floats are not subject to
the side loads. Rigid floats are to be designed for vertical, horizontal, and side loads
distributed along the length of the float.
(9) Design and/or support of the forward part of bag type floats should be
evaluated for maximum design speeds to prevent collapse or significant distortion of
the bag while in flight.
(10) Resistance to puncture and abrasion at attach/wear points is an
important design consideration. Girt or attachment design loads should be sufficient to
withstand the maximum imposed design loads.
(11) Occupant Egress and Survival. Each practicable design measure should
be taken to minimize the probability that the behavior of the rotorcraft would cause
immediate injury to the occupants or prevent evacuation of the rotorcraft after an
emergency landing on water. Emergency exits should be located such that they are
above the waterline and will not be blocked by the inflated or partially inflated floats,
impeding evacuation of the rotorcraft. The flotation time and trim of the rotorcraft
should allow the occupants to evacuate the rotorcraft. i.e., the rotorcraft should remain
sufficiently upright and in adequate trim to permit safe and orderly evacuation of all
personnel. For configurations which are considered to have critical occupant egress
capabilities due to float proximity, an actual demonstration of egress may be required.
When a demonstration is required, it may be conducted on a full-scale rotorcraft
actually immersed in a calm body of water or using any other rig/ground test facility
shown to be representative. The demonstration should show that floats do not impede
a satisfactory evacuation.
(12) Rotorcraft Flight Manual. The Rotorcraft Flight Manual should contain the
information pertaining to the emergency flotation system. This material should include:
Page MG 10 - 5
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.