FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 892

PDF page 892 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 892
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

              (A) Low acceleration schedule

              (B) Low maximum fuel stop

             (C) Low fuel pump output

             (D) Restrictions between the fuel control and the combustor

                   (ii)   The proposed emergency ratings (OEI) may preclude the use of a
topping check to uncover the above problems; therefore the following procedures are
advanced which can be used either separately or in combination with other approved
methods to assure that the required fuel flow is available.

                    (iii)   During engine acceleration the fuel flow rate is considerably higher
when compared with the normal steady state condition. This fact can be used to verify
the availability of OEI fuel flow. The verification can be done by a direct measurement
of fuel flow during an acceleration or derived indirectly from the engine acceleration
rate.  It is envisaged that the determination of fuel flow by these procedures should be
done by some automatic means.

               (iv   Figure AC 27 MG 9-1 is a bypass technique in which some of the fuel
controls output is routed away from the engine and back to tank. This forces the fuel
control onto the acceleration schedule in order to maintain gas generator speed. The
design of the system should ensure that with the bypass flowing the fuel control outlet
pressure and flow at the OEI ratings are simulated. The bypass system can be either
permanently installed and operated in flight, (Failure Malfunction Effects Analysis must
be provided), or as an item of ground test equipment. The quantity of fuel bypassed
should be equivalent to the worst case difference between fuel flow at the 30-second
rating and typical power assurance power levels. However, trend monitoring and
service history may provide the basis of an alternative to periodic measurement.

         (2) Limiters. A means must be provided to assure that a lower than required
(for OEI power) limiter setting does not exist. Limiters that could prohibit reaching OEI
power are as follows:

                  (i)   Ng - Maximum Compressor Speed Limiter or Governor

                   (ii)   Measured gas temperature limiter

                    (iii)   Output shaft torque limiter

               (iv)  Np limiter or power turbine governor-power turbine governors can be
verified at lower than OEI power conditions.

              (v)   Fuel flow limiter or maximum fuel flow stop-Fuel flow limiting has been
addressed in previous paragraphs.


Page MG 9 - 4

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →