Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 2 4/25/06
(5) Should subsequent usage of the rotorcraft encompass a mission for
which the original structural substantiation did not account, the effects of this new
mission environment on the frequency of loading and structural substantiation should be
addressed and where practicable, in the interest of safety, a reassessment made. If this
reassessment indicates the necessity for revised retirement times, those new times may
be limited to aircraft involved in the added mission provided.
(i) Proper part re-identification is established;
(ii) a Rotorcraft Flight Manual (RFM) supplement outlining limitations is
approved;
(iii) an airworthiness limitations section supplement is approved; or
(iv) an appropriate combination of part re-identification, RFM supplement,
or airworthiness limitation section supplement is approved.
(B) Loading Spectrum. The spectrum allocating percentage of time or
frequencies of occurrence to flight conditions or maneuvers is to be based on the
expected usage of the rotorcraft. This spectrum is to be such that it is unlikely that
actual usage will subject the structure to damage beyond that associated with the
spectrum. Considerations to be included in developing this spectrum should include
prior knowledge based on flight history recorder data, design limitations established in
compliance with § 27.309, and recommended operating conditions and limitations
specified in the rotorcraft flight manual. The distribution of times at various forward flight
speeds should reflect not only the relation of these speeds to VNE but also the
recommended operating conditions in the rotorcraft flight manual that govern Vc or
cruise speed. Where possible, it is desirable to conduct the flight strain-gauge program
by simulating the usage as determined above, with continuous recording of stresses
and loads, thus obtaining directly the stress and load spectra for structural elements.
(7) The seventh major area is the dynamic loading and response requirements
of §§ 27.241, 27.251, and 27.629 for vibration and resonance frequency determination
and separation for aeroelastic stability and stability margin determination for dynamically
critical flight structure. Critical parts, locations, excitation modes, and separations are to
be identified and substantiated. This substantiation should consist of analysis
supported by tests and tests that account for repeated loading effects and environment
exposure effects on critical properties, such as stiffness, mass, and damping. Initial
stiffness, residual stiffness, proper critical frequency design, and structural damping are
provided as necessary to prevent vibration, resonance, and flutter problems.
(i) All vibration and resonance critical composite structure are identified
and properly substantiated.
(ii) All flutter-critical composite structures are identified and properly
substantiated. This structure must be shown by analysis to be flutter free to 1.1 VNE (or
Page MG 8 - 30
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.