Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
4/25/06 AC 27-1B, Chg 2
flight condition. Consideration can be given to the use of scatter factors in determining
the sufficiency of data points. In some instances, the critical weight, center of gravity,
and altitude ranges for the various maneuvers can be based on past experience with
similar design. This procedure is acceptable where adequate flight tests are performed
to substantiate such selections. The combinations of flight parameters that produce the
most critical stress levels should be used in the fatigue evaluation.
(vi) FREQUENCY OF LOADING.
(A) Types of Operation.
(1) The probable types of operation (transport, utility, etc.) for the
rotorcraft should be established. The type of operation can have a major influence on
the loading environment. In the past, rotorcraft have been substantiated for the most
critical general types of operation with some consideration of special, occasional types
of operation. To assure that the most critical types of operation are considered, each
major rotorcraft structural component should be substantiated for the most critical types
of operation as established by the manufacturer. The types of operation shown below
should be considered and, if applicable, used in the substantiation:
(i) Long flights to remote sites (low ground-air-ground cycles but high
cruising speeds).
(ii) Typical, general types of operation.
(iii) Short flights as used in logging operations.
(2) One means is to substantiate for the most severe type of operation;
however, this method is not always economically feasible.
(3) A second means is to quantify the influence of mission type on fatigue
damage by adding to or replacing hour limitations by flight cycle limitations (if properly
defined and easily identifiable by the crew, for example: one landing, one load
transportation). A special type of flight hour limitation replacement using factorization of
flight hours for multiple types of operations may be feasible if continuing manufacturer’s
technical support is provided and documented; i.e., the manufacturer either provides the
factorization analyses or checks them on a continuing basis for each rotorcraft.
(4) Where one or more of the above operations are not among the
general uses intended for the rotorcraft, the rotorcraft flight manual should state in the
limitations section that the intended use of the rotorcraft does not include certain
missions or repeated maneuvers (i.e., logging with its high number of takeoffs/landings
per hour). A note to this effect should also appear in the rotorcraft airworthiness
limitations section of the maintenance manual prepared in accordance with § 27.1529.
Page MG 8 - 29
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.