FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 884

PDF page 884 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 884
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                     3/31/2014


This may be accomplished by appropriate analytical means supplemented, when
deemed necessary, by strain sensitive coatings or photoelastic methods. The
distribution and number of strain gauges should define the load spectrum adequately for
each part essential to the safe operation of the rotorcraft as identified in
§ 27.571(a)(1)(i). Other devices such as accelerometers may be used as appropriate.

               (2) The corresponding flight parameters (airspeed, rotor RPM, center of
gravity accelerations, etc.) should also be recorded simultaneously by appropriate
methods. This is necessary to correlate the loads and stresses with the maneuver or
operating conditions at which they occurred.

               (3) The instrumentation system should be adequately calibrated and
checked periodically throughout the flight strain measurement program to ensure
consistent and accurate results.

             (C) Parts to be Strain-Gauged. Fatigue critical portions of the rotor
systems, control systems, landing gear, fuselage, and supporting structure for rotors,
transmissions, and engine are to be strain-gauged. For rotorcraft of unusual or unique
design, special consideration might be necessary to ensure that all the essential parts
are evaluated.

             (D) Flight Regimes and Conditions to be investigated.

               (1) Typical flight and ground conditions to be investigated in the flight
strain measurement program are given in paragraphs c. and d. of section AC 27 MG 11
of this AC.

               (2) The determination of flight conditions to be investigated in the flight
strain measurement program should be based on the anticipated use of the rotorcraft
and, if available, on past service records for similar designs. In any event, the flight
conditions considered appropriate for the design and application should be
representative of the actual operation in accordance with the rotorcraft flight manual. In
the case of multiengine rotorcraft, the flight conditions concerning partial engine-out
operation should be considered in addition to complete power-off operation. The flight
conditions to be investigated should be submitted in connection with the flight evaluation
program.

               (3) The severity of the maneuvers investigated during the flight strain
survey should be at least as severe as the maximum likely in service.

               (4)  All flight conditions considered appropriate for the particular design
are to be investigated over the complete rotor speed, airspeed, center of gravity,
altitude, and weight ranges to determine the most critical stress levels associated with
each flight condition. The temperature effects on loads as affected by elastomeric
components are to be investigated. To account for data scatter and to determine the
stress levels present, a sufficient amount of data points should be obtained at each


Page MG 8 - 28

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →