FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 883

PDF page 883 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 883
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

4/25/06                                       AC 27-1B, Chg 2


                 (iv) Locations of potential fatigue damage identified by fatigue analysis.

               (v) Locations where the stresses in adjacent elements will be at a
maximum with an element in the location failed.

                 (vi) Partial failure locations in an element where high stress
concentrations are present in the remaining structure.

                   (vii) Locations where detection would be difficult.

              (viii)Design details that are prone to fatigue or other damage indicated by
service experience of similarly designed components.

               (3)  In addition, the areas of probable damage from sources such as a
severe corrosive or fretting environment, a wear or galling environment, or a high
maintenance environment should be determined from a review of the design and past
service experience.

             (C) The stresses and strains (steady and oscillatory) associated with all
representative steady and maneuvering operating conditions expected in service.

             (D) The frequency of occurrences of various flight conditions and the
corresponding spectrum of loadings and stresses.

              (E) The fatigue strength, fatigue crack propagation characteristics of the
materials used and of the structure, and the residual strength of the damaged structure.

              (F) Inspectability, inspection methods, and detectable flaw sizes.

            (G) Variability of the measured stresses of paragraph g(6)(iv)(C) above,
the actual flight condition occurrences of paragraph g(6)(iv)(D) above, and the fatigue
strength material properties of paragraph g(6)(iv)(E).

              (v)  FLIGHT STRAIN MEASUREMENT PROGRAM.

              (A) General. Subsequent to design analysis, in which aircraft loads and
associated stresses are derived, the stress level and loads are to be verified by a
carefully controlled flight strain measurement program. (This guidance is similar to that
of AC 27-1B, MG 11, Chg 1.)

              (B) Instrumentation.

               (1) The instrumentation system used in the flight strain measurement
program should accurately measure and record the critical strains under test conditions
associated with normal operation and specific maneuvers. The location and distribution
of the strain gauges should be based on a rational evaluation of the critical stress areas.


                                                       Page MG 8 - 27

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →