Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 2 4/25/06
(iv) Additional Considerations for FATIGUE AND FLAW TOLERANCE
Evaluations.
(A) Experience with the application of methods of fatigue and flaw
tolerance evaluations indicates that a relevant test background should exist in order to
achieve the design objective. It is the general practice within industry to conduct flaw
tolerance tests for design information and guidance purposes. It is crucial that the
critical structure be identified and tested to the proper flight and ground loads. In the
fatigue and flaw tolerance evaluation the following items must be considered:
(B) Identification of the structure to be considered in each evaluation (a
failure mode and effects analysis or similar method should be used).
(1) Identification of Principal Structural Elements. Principal structural
elements are those that contribute significantly to carrying flight and ground loads and
whose failure could result in catastrophic failure of the rotorcraft. Typical examples of
such elements are:
(i) Rotor blades and attachment fittings.
(ii) Rotor heads, including hubs, hinges, and some main rotor dampers.
(iii) Control system components subject to repeated loading, including
control rods, servo structure, and swashplates.
(iv) Rotor supporting structure (lift path from airframe to rotor head).
(v) Fuselage, including stabilizers and auxiliary lifting surfaces.
(vi) Main fixed or retractable landing gear and fuselage attachment
structure.
(2) Identification of Locations Within Principal Structural Elements to be
Evaluated. The locations of damage to structure for damage tolerance evaluation can
be determined by analysis or by fatigue test on complete structures or subcomponents.
However, tests will be necessary when the basis for analytical prediction is not reliable,
such as for complex components. If less than the complete structure is tested, care
should be taken to ensure that the internal loads and boundary conditions are valid.
The following should be considered:
(i) Strain gauge data on undamaged structure to establish points of high
stress concentration as well as the magnitude of the concentration.
(ii) Locations where analysis shows high stress or low margins of safety.
(iii) Locations where permanent deformation occurred in static tests.
Page MG 8 - 26
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.