FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 875

PDF page 875 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 875
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

4/25/06                                       AC 27-1B, Chg 2


design considerations are also needed to ensure the safety of structure with secondary
bonds (i.e., random, but an unacceptable numbers of weak bonds discovered in
service). Unless the ultimate strength of each critical bonded joint can be reliably
substantiated in production by NDI techniques (or other equivalent, approved
techniques), then the limit load capability should be ensured by any of the following or a
combination thereof.

               (1) Consider isolated disbonds and weak bonds (represented by zero
bond strength) in structural elements that use secondary bonding for primary load
transfer. The associated disbond size should be up to the limitations provided by
redundant design features (i.e., mechanical fasteners or a separate bonding detail).
The structure containing such damage should be shown to carry limit load by tests,
analyses, or some combination of both. For purposes of test or analysis demonstration,
each disbond should be considered separately as a random occurrence (i.e., it is not
necessary to demonstrate residual strength with all structural elements disbonded
simultaneously).

               (2) Each critical bonded joint on each production article should be proof
tested to the critical limit load.

               (3)  Critical bonded joints that have high static margins of safety (e.g.,
some rotor blades) may be acceptable, provided there is satisfactory service history of
like or similar components.

             (D) The fatigue load spectrum developed for fatigue testing and analysis
purposes should be representative of the anticipated service usage. Low amplitude
load levels that can be shown not to contribute to fatigue damage may be omitted
(truncated). Reducing maximum load levels (clipping) is generally not accepted.

              (E) Environmental effects (temperature and humidity representative of the
expected service usage) on the static or fatigue behavior and damage growth should be
considered. Unless tested in the environment, appropriate environmental knock down
factors for the static and the fatigue test articles should be derived and applied in the
evaluation.

              (F) Variability in fatigue behavior should be covered by appropriate load
and/or life scatter factors and these factors should take into account the number of
specimens tested.

            (G) The following Figure AC 27 MG 8-2 illustrates the extent of the impact
damage that needs to be considered in the flaw tolerance evaluation.





                                                       Page MG 8 - 19

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →