FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 874

PDF page 874 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 874
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 2                                                         4/25/06


assuming such damage occurs within the operational life of the structure. When this
damage occurs, the remaining structure will withstand reasonable loads without failure
or excessive structural deformations until the damage is detected and the component is
either repaired to restore ultimate load capability or retired.

                   (ii)  FLAW TOLERANCE EVALUATION - GENERAL. The nature and
extent of the required analysis or tests on complete structures or portions of the primary
structure can be based on applicable previous fatigue or damage tolerant designs,
construction, tests, and service experience on similar structures. In the absence of
experience with similar designs, FAA/AUTHORITY-approved structural development
tests of components, subcomponents, and elements should be performed. The
following considerations are unique to the use of composite material systems and
should be observed for the method of substantiation selected by the applicant.
Rotorcraft structure provides a broad range of composite applications that are quite
different in terms of functionality, geometry, and inspectability. These include the rotors,
the drive shafts, the fuselage, control system components (e.g., push-pull rods), and the
control surfaces. When selecting the approach, attention should be given to the
composite application under evaluation, the type of potential damage or degradation of
the structural design details, the materials used, and margin over flight loads. Whatever
the approach that may be selected, the following considerations will apply for tests and
analysis:

              (A) The test articles should be fabricated and assembled in accordance
with production specifications and processes so that the test articles are representative
of production structure.

              (B) The test articles should include material imperfections whose extent is
not less than the limits established under the inspection and acceptance criteria used
during the manufacturing process and consistent with the inspection techniques used in
service (e.g., visual, ultrasonic, X-ray). The initial extent of these imperfections should
be discussed and agreed with the FAA/AUTHORITY, taking into account experience in
manufacturing and routine in-service inspections. Typical defects to be considered
include but are not limited to the following:

               (1) Disbonds and weak bonds (considered as disbonds).

               (2) Delaminations, fiber waviness, porosity, voids.

               (3) Scratches, gouges, and penetrations.

               (4) Impact damage.

             (C) The use of composite secondary bonding in manufacturing or
maintenance requires strict process and quality controls to achieve the reliability needed
to use such technology in critical structures (reference AC 21-26). Assuming good
process and quality controls, service history has shown that additional damage tolerant


Page MG 8 - 18

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →