FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 873

PDF page 873 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 873
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

4/25/06                                       AC 27-1B, Chg 2


                    (iii)   Allowables should be used as specified in § 27.613. These
allowables may be generated at the lamina, laminate, or specific design feature level
(e.g. filled hole, lap joint, stringer run-out, etc.), provided they accurately reflect the
actual value and variability of the structural strength for the critical failure modes being
considered, at each point design where margins need to be established.

               (iv)  The static test articles should be fabricated and assembled in
accordance with production specifications and processes so that they are
representative of production structure including defects consistent with the limits
established by manufacturing acceptance criteria.

              (v)  The material and processing variability of the composite structure
should be considered in the static strength substantiation. This can be achieved by
establishing sufficient process and quality controls to manufacture structure and reliably
substantiate the required strength in tests and analyses, which support a building block
approach.  If sufficient process and quality controls cannot be achieved, it may be
necessary to account for greater variability with special factors (§ 27.619) applied to the
design. Such factors should be accounted for in the component static tests or analysis.

               (vi)    It should be shown that impact damage (or other minor discrete
source damage) that can be realistically expected from manufacturing and service, but
not more than the established threshold of detectability for the selected inspection
procedure, will not reduce the structural strength below ultimate load capability. This
static strength capability can be shown by analysis supported by test evidence, or by a
combination of tests at the coupon, element, subcomponent, and component levels.
Later discussions in this AC paragraph address the issues associated with damage in
excess of that considered in g(5) of this AC paragraph and drops in residual strength
below ultimate load capability (reference paragraph g(6)) below.

         (6) The sixth area is the fatigue evaluation of structure requirements of
§ 27.571.

                  (i)   FATIGUE EVALUATION - BACKGROUND. The static strength
determination required by §§ 27.305 and 27.307 establishes the ultimate load capability
for composite structures that are manufactured, operated, and maintained with
established procedures and conditions. The fatigue tolerance evaluation required by
§ 27.571 establishes procedures that allow the composite structure to retain the
intended ultimate load capability when subjected to expected fatigue loads and
conditions during its operational life. The procedures established by the fatigue
tolerance evaluation include component retirement times and/or inspection intervals.
The fatigue tolerance evaluation requires a flaw tolerance assessment that assumes
that the baseline ultimate strength capability might be compromised by damage caused
by fatigue, environmental effects, intrinsic discrete flaws, or accidental damage. The
flaw tolerance assessment establishes procedures that do not allow the static strength
capability to degrade below the ultimate strength capability for extended periods,



                                                       Page MG 8 - 17

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →