FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 868

PDF page 868 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 868
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 2                                                           4/25/06


the polymer behaves like a “glassy” solid and above which it behaves like a “rubbery”
solid, i.e., it is the temperature at which there is a very rapid change in physical
properties. In actuality, the change from a hard polymeric material to a rubbery material
takes place over a narrow temperature range. A composite material will experience a
drastic reduction in matrix controlled mechanical material properties when loaded in this
temperature range. Since the resin (matrix) is the critical structural constituent in a
composite and since Tg exceedance is critical to structural integrity, Tg determination is
necessary. The Tg margin methodology of MIL-HDBK-17 should be implemented, i.e.,
the wet glass transition temperature (Tg) should be 50° F higher than the maximum
structural temperature (see definition in paragraph e(24) of this AC paragraph). For any
type of resin or adhesive, an acceptable temperature margin using MIL-HDBK-17
techniques (e.g., consideration of limited high temperature excursions) or equivalent
methodologies based on tests or experience or both should be established and
approved early in the certification process.

              (v)   Local design values should be established by analysis and
characterization tests and approved for specific structural configurations (point designs),
which include the effects of stress risers (e.g., holes, notches, etc.) and structural
discontinuities (e.g., joints, splices, etc.). Proper determination of these values for
full-scale design and test should be considered one of the most critical building blocks in
substantiating and evaluating a composite structure. These transitional load transfer
areas typically produce the highest stresses (and strains) and serve as the nucleation
sites for many of the failures (including those due to the relatively low interlaminar
strength of composites) that occur in service in a full-scale part or assembly. Small
scales tests (such as coupon, element, and subcomponent tests), or equivalent
approved testing programs, and analytical techniques should be carefully designed,
prepared, and approved to evaluate potential “hot spots” and provide accurate
simulations and representations of full-scale article stresses and strains in the critical
transition areas. Proper certification work in this area will ensure initial safety and
continued airworthiness in full-scale production articles.

               (vi)  The design strain level for each major component and material system
should be established such that specified impact damage considerations are defined
and properly limited. The effects of the strain levels may be established for each
composite material using small-scale characterization tests and then the results should
be used to establish or verify the maximum allowable design strain level for each
full-scale article. The maximum allowable design strain values selected should also
take into account the reliability and confidence levels established for the relevant
portions of the quality system. This methodology is necessary because the amount and
size of flaws in the production article may restrict the allowable level of design strain. In
a no-flaw-growth design, the maximum specified impact damage and manufacturing
flaw size at the most critical location on the part will be a major factor in determining the
maximum allowable elastic strain. This design approach is currently selected for nearly
all civil and most military applications; since, under normal conditions, only visual
inspections are required in the field (unless unusual external damage circumstances
such as a hail storm occur) to maintain the initial level of airworthiness (safety).


Page MG 8 - 12

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →