FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 865

PDF page 865 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 865
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

4/25/06                                       AC 27-1B, Chg 2


certification of a composite structure is an incremental, building block process which
involves phased FAA/AUTHORITY involvement and incremental approval in each of the
various areas outlined herein. This approach will minimize the risk associated with
substantiation of the full-scale article.  It is strongly recommended that a certification
team approach, involving fabrication, quality, and engineering specialists from both the
applicant and FAA/AUTHORITY, be used for composite structural substantiation.

The team should assure that permanent documentation of the building block approach
in the form of reports or other FAA/AUTHORITY-acceptable documents are included in
the certification data package. The documentation includes but is not limited to the
structural substantiation reports (both analysis and test), manufacturing processes and
quality control, and Instructions for Continued Airworthiness (maintenance, overhaul,
and repair manuals). FAA/AUTHORITY engineering approves the Airworthiness
Limitations Section of the maintenance manual. Engineering practices for many of the
areas identified below are available in MIL-HDBK-17.

         (1) The first area is the fabrication requirements of § 27.605:

                  (i)   The quality system should be developed considering the critical
engineering, manufacturing, and quality requirements along with a guidance standard
such as AC 21-26, “Quality Control for the Manufacture of Composite Materials." This
ensures that all special engineering, or manufacturing quality instructions for
composites are presented, evaluated, documented, and approved, using drawings,
process and manufacturing specifications, standards, or other equivalent means. This
should be one of the early phases of a composite structure certification program, since
this represents a major building block for sequential substantiation work. Some
important concepts of AC 21-26 are included below.

                   (ii)   Specific allowable defect limits on, for example, fiber waviness, warp
defects, fill defects, porosity, hole edge effects, edge defects, resin content, large area
disbonds , and delaminations, etc., for a particular material system component, laminate
design, detailed part, or assembly should be jointly established by engineering,
manufacturing, and quality and the associated inspection programs for defect detection
created, validated, and approved. Each critical engineering design should consider the
variability of the manufacturing process to determine the worst-case effects (maximum
waviness, disbonds, delaminations, and other critical defects) allowed by the reliability
limitations of the approved inspection program.

                    (iii)     If bonds or bond lines such as those typical of rotorcraft rotor blade
structure are used, special inspection methods, special fabrication methods or other
approved verification methods (e.g., engineering proof tests, reference paragraph g(5)
of this AC paragraph) should be provided to detect and limit disbonds or understrength
bonds.

               (iv)   Structurally critical composite construction fabrication process and
procurement specifications, for fabricating reproducible and reliable structure, must be


                                                        Page MG 8 - 9

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →