FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 863

PDF page 863 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 863
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

4/25/06                                       AC 27-1B, Chg 2


        (46) PASSIVE MULTIPLE LOAD PATH. Structure providing load paths with
one or more of the members (or areas of a member) relatively unloaded until failure of
the other member or members.

        (47) ACCIDENTAL DAMAGE FLAWS. Discrete damage that may occur in
service use or in manufacturing due to impacts or collisions, such as dents, scratches,
gouges, abrasions, disbonds, splintering, and delaminations.

        (48) MANUFACTURING-RELATED FLAWS. Intrinsic imperfections related to
manufacturing operations, processing, or assembly such as voids, gaps, porosity,
inclusions, fiber dislocation, disbonds, and delaminations.

        (49) FATIGUE/ENVIRONMENTAL FLAWS. Structural damage related to
fatigue or environmental effects such as delaminations, disbonds, splintering, or
cracking.

        (50) DESIGN LIMIT LOADS. The maximum loads to be expected in service,
as defined by § 27.301(a).

        (51) AS-MANUFACTURED. Product or component that has passed the
applicable quality control process and has been found to conform to the approved
design within the allowable tolerances.

        (52) RESIDUAL STRENGTH. The strength retained for some period of
unrepaired use after a failure or partial failure due to fatigue or accidental or discrete
source of damage.

        (53) PRINCIPAL STRUCTURAL ELEMENT (PSE). A structural element that
contributes significantly to the carrying of flight or ground loads and whose failure can
lead to catastrophic failure of the rotorcraft.

        (54) COUPON. A small test specimen (e.g., usually a flat laminate) for
evaluation of basic lamina or laminate properties or properties of generic structural
features (e.g., bonded or mechanically fastened joints).

        (55) POINT DESIGN. An element or detail of a specific design that is not
considered generically applicable to other structure for the purpose of substantiation
(e.g., lugs and major joints). Such a design element or detail can be qualified by test or
by a combination of test and analysis.

        (56) ELEMENT. A generic element of a more complex structural member
(e.g., skin, stringers, shear panels, sandwich panels, joints, or splices).

        (57) DETAIL. A non-generic structural element of a more complex structural
member (e.g., specific design configurated joints, splices, stringers, stringer runouts, or
major access holes).


                                                        Page MG 8 - 7

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →